Reed Valves - Page 2
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: Reed Valves

  1. #11
    PWCToday Guru Dan87951's Avatar
    Join Date
    Jun 2004
    Location
    Lansing, MI
    Age
    37
    Posts
    440

    Re: Reed Valves

    Pretty sure this is the pulse line the fuel pump? The hose has been cut.
    Last edited by Dan87951; 05-28-2017 at 09:34 PM.
    04' Shorelander Double Trailer
    98' Sea Doo SPX Mint
    96' Sea Doo HX Mint
    95' Sea Doo XP800 Mint
    95' Sea Doo XP800 - Rescue project (almost done)
    99' Sea Doo XPL - rescue (project on hold)
    97' Tigershark Daytona 1000 - Another rescue project (see videos below)
    My Jet Ski videos below.
    https://www.youtube.com/playlist?lis...wmp0jqpvLFpgmZ

  2. #12
    PWCToday Newbie
    Join Date
    Jan 2019
    Location
    Florida
    Age
    41
    Posts
    2

    Re: Reed Valves

    Did you ever find out where it goes?

    Iím having the exact same question.

    Thanks!

  3. #13
    Frequent Poster Associated98's Avatar
    Join Date
    May 2014
    Location
    Cottage Grove, MN
    Posts
    292

    Re: Reed Valves

    Impulse hose goes from a nipple in between the mag and center reed valve assemblies on the upper crankcase half to the fuel pump.
    Own:
    98' TS1000R
    97' Daytona 1000
    97' Daytona 1000
    97' Daytona 1000
    Owned:
    94' Montego (my first) sold
    95' Daytona sold
    95' Daytona parted out
    95' Barracuda sold
    96' Montego sold
    96' Daytona (the one that got away...) sold
    96' Monte Carlo 900 sold
    97' Daytona 1000 clean and beautiful. You will be missed.
    97' Daytona 1000 sold
    99' TS770R sold

  4. #14
    PWCToday Newbie
    Join Date
    Jan 2019
    Location
    Florida
    Age
    41
    Posts
    2

    Re: Reed Valves

    Thanks, that helped out a lot.

    There’s two more questions I can’t find answer to.
    I hope you or someone else is able to help me next to the starter on the bell house there’s a nipple, I can’t figure out what connects to it. C0F180C9-F367-4D7A-A1F6-9FD216CC5240.jpeg

    Do you know what connects to it?

    Also on the right side of the hull, inside runs a small line, to something that looks like a pisser, little black thing on the outside. I don’t know what it connects to either, any thoughts?

    I really appreciate your time and help on this.

  5. #15
    Frequent Poster Associated98's Avatar
    Join Date
    May 2014
    Location
    Cottage Grove, MN
    Posts
    292

    Re: Reed Valves

    There is a bladder or "bellows" as it's properly called attached there. They are ALWAYS ripped or missing. They are also impossible to find. I cap mine off with a vacuum cap but this is not the correct way to do it. The bellows expands as the air inside the flywheel housing heats up from engine heat and also expands. If you just cap it off like me, eventually it will push a hole in mag cover gasket and let water in. This is something you do not want. Say goodbye to your Bendix, starter, and flywheel once you put it away for the season. Come spring it will all be rusted and the Bendix seized. I do it cause I'm cheap, but I also haven't had a problem.

    If the outlet your talking about looks like a tiny rubber hood scoop then it's ether the breather for the fuel tank or oil tank. I don't recall the 97/98 Daytona/tsr hulls having those, only seen them on my 99' tsr I had a while back. But I could be wrong.
    Last edited by Associated98; 04-26-2019 at 08:25 PM.
    Own:
    98' TS1000R
    97' Daytona 1000
    97' Daytona 1000
    97' Daytona 1000
    Owned:
    94' Montego (my first) sold
    95' Daytona sold
    95' Daytona parted out
    95' Barracuda sold
    96' Montego sold
    96' Daytona (the one that got away...) sold
    96' Monte Carlo 900 sold
    97' Daytona 1000 clean and beautiful. You will be missed.
    97' Daytona 1000 sold
    99' TS770R sold

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.2.0