Largest PWC

Superstore

Collapse

how to get graphics to fit...

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • kawi105
    PWCToday.com Is My Home Away From Home
    • Nov 2007
    • 3729
    #1

    how to get graphics to fit...

    on the rear half of the SXR.

    I was putting graphics on today, and theres like 4 different curves to combat. How do you deal with this?

    I got one side done and it looks good from 4 feet away, but i want this side a little better.

    Tags: None
  • Mr Bojangles
    Resident Guru
    • Aug 2009
    • 1126
    #2
    Re: how to get graphics to fit...

    You need to heat and strech them carefully. Wet the sufave down with soapy water, the place the graphics down, then heat. The soapy water allows you to remove the graphics without messing them up
    1989 Kawasaki X2
    2005 Yamaha XLT1200
    2008 Water Craft Factory hull



    Truck Bed Launch System - http://www.pwctoday.com/f26/mr-bojan...ml#post2683099

    Comment

    • kawi105
      PWCToday.com Is My Home Away From Home
      • Nov 2007
      • 3729
      #3
      Re: how to get graphics to fit...

      thanks, i did everything you said cept heat. ill try that today.

      Comment

      • Mr Bojangles
        Resident Guru
        • Aug 2009
        • 1126
        #4
        Re: how to get graphics to fit...

        I forgot to add, make solute not to over heat it or it will bubble or tear. Use a hair dryer or I have just did it out in the sun in Florida. Once your done and if you have little bubbles, just put it in the sun and use a needle and pop them and flatten them out and you will be set
        1989 Kawasaki X2
        2005 Yamaha XLT1200
        2008 Water Craft Factory hull



        Truck Bed Launch System - http://www.pwctoday.com/f26/mr-bojan...ml#post2683099

        Comment

        • kawi105
          PWCToday.com Is My Home Away From Home
          • Nov 2007
          • 3729
          #5
          Re: how to get graphics to fit...

          it went well to day. it was a lot easier thanks!

          Comment

          • kawi105
            PWCToday.com Is My Home Away From Home
            • Nov 2007
            • 3729
            #6
            Re: how to get graphics to fit...





            Thanks Mr. Bojangles and DK1Designs!
            Last edited by kawi105; 02-14-2010, 10:08 PM.

            Comment

            • Mr Bojangles
              Resident Guru
              • Aug 2009
              • 1126
              #7
              Re: how to get graphics to fit...

              Not a problem, it looks great!
              1989 Kawasaki X2
              2005 Yamaha XLT1200
              2008 Water Craft Factory hull



              Truck Bed Launch System - http://www.pwctoday.com/f26/mr-bojan...ml#post2683099

              Comment

              • kawi105
                PWCToday.com Is My Home Away From Home
                • Nov 2007
                • 3729
                #8
                Re: how to get graphics to fit...

                yeah, im pretty happy since its my first graphic kit install.

                Comment

                • attnondeck
                  Spongebob
                  PWCToday.com Is My Home Away From Home
                  • Sep 2008
                  • 9414
                  #9
                  Re: how to get graphics to fit...

                  FRANKOOOOOO!!!!! SICK!!!!!!!!! lovin it kid!!!!!!!
                  Brendan

                  1990 SN SJ 701 1990 SN Super Jet 650 Winter build
                  1990 550SX modded to piss
                  1994 FX1
                  And a Blaster for good measure




                  Comment

                  • DK1Designs
                    PWCToday.com Is My Home Away From Home
                    • Jun 2007
                    • 2083
                    #10
                    Re: how to get graphics to fit...

                    Graphics look good, Frank. Glad everything lined up good, lol.
                    Derrick Kemnitz Jr.
                    3x Regional Champion - 2x WC National Champion - 1x World Champion
                    The Ski Clinic - The BOB Hull - DK1Designs - Hydro-Turf - MotoOption Clothing - Quakysense - D&H Enterprises

                    Comment

                    • Russell2sx
                      Top Dog
                      • Oct 2009
                      • 1633
                      #11
                      Re: how to get graphics to fit...

                      sweet!!!!! how much was that kit????

                      Comment

                      • DK1Designs
                        PWCToday.com Is My Home Away From Home
                        • Jun 2007
                        • 2083
                        #12
                        Re: how to get graphics to fit...

                        http://www.dk1designs.com/sx-r.html


                        Second kit.
                        Derrick Kemnitz Jr.
                        3x Regional Champion - 2x WC National Champion - 1x World Champion
                        The Ski Clinic - The BOB Hull - DK1Designs - Hydro-Turf - MotoOption Clothing - Quakysense - D&H Enterprises

                        Comment

                        • OptimaRacing
                          I dream skis
                          • Mar 2006
                          • 738
                          #13
                          Re: how to get graphics to fit...

                          Nice! That looks awesome Frank! Nice work Derrick! Way to rep the OPT as well!

                          www.OptimaRacing.com
                          Email: [email protected] with any questions. Thank you!
                          sigpic

                          Comment

                          • kawi105
                            PWCToday.com Is My Home Away From Home
                            • Nov 2007
                            • 3729
                            #14
                            Re: how to get graphics to fit...

                            of course i had to rep!! haha

                            Comment

                            • kawi105
                              PWCToday.com Is My Home Away From Home
                              • Nov 2007
                              • 3729
                              #15
                              Re: how to get graphics to fit...

                              Originally posted by Russell2sx View Post
                              sweet!!!!! how much was that kit????
                              Compared to ther graphics its a sweet price for tyhe original look.

                              Comment

                              Previous 1 2 template Next
                              Working...
                              X