Search Results - PWCToday
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: bbar; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Re: kawasaki 650 -surging after running for an hour then quitting

    Shop I took it to said stator was good. They said the aftermarket cdi I put in last year was bad. I put a used oem cdi in; spark was back and ski started right up but didn't run well and then died...
  2. Re: kawasaki 650 -surging after running for an hour then quitting

    Carb rebuilt last year . Fuel lines cleaned and checked again 2 weeks ago. Problem now is electrical because I have no spark (again) but I don't know why. Thanks.
  3. Re: kawasaki 650 -surging after running for an hour then quitting

    Please disregard last post. Seller wrote wrong number on cdi I bought but I made out original factory numbers and it is a 3721. So back to question of why it ran like crap and then quit. Thanks.
  4. Re: kawasaki 650 -surging after running for an hour then quitting

    More info. Looks like used cdi that I bought is not the same part number as mine.One I bought is a 21119-3702 (which is for an x-2?) and parts list says mine takes a 21119-3721.
  5. Re: kawasaki 650 -surging after running for an hour then quitting

    Just tried it again this morning. Started and idled but would not turn up at all. After about 30 seconds, quit. Now no spark.
  6. Re: kawasaki 650 -surging after running for an hour then quitting

    Had a shop check all electrics and they determined the cdi was bad. I purchased a used oem cdi(same part number as mine) from a '92 ts. Put it in and ski started right up but won't rev up and surges...
  7. Replies
    2
    Views
    785

    Re: part number for front tow grommet -91 sc

    yes, thank you.
  8. Replies
    2
    Views
    785

    part number for front tow grommet -91 sc

    the parts diagrams don't show the number for the front white plastic grommet that has the big nut on the bottom of it and goes through the hole in the rubrail at the very front(and rear) of the ski...
  9. Re: kawasaki 650 -surging after running for an hour then quitting

    .....
  10. kawasaki 650 -surging after running for an hour then quitting

    Hi, kawasaki 650 in a '91 sea couch. Last 2 times out, motor has run great for 45 minutes to 1 hour, then starts to lose power and surge, then eventually just runs at low rpm no matter where I try to...
  11. Replies
    5
    Views
    1,263

    Re: kawasaki 650 pump questions

    thank you. If I'm reading the schematic correctly, there doesn't seem to be a bushing and seal at the tail cone end and I'm pretty sure both my pumps do. The bushing is what is turning when...
  12. Replies
    5
    Views
    1,263

    kawasaki 650 pump questions

    Hi, I have a '91 sea couch and a '90 stand up. I have removed impellers and R&R'd the pumps but have never dealt with the bearings/seals in the pumps; always send them to a pro. Want to tackle this...
  13. Replies
    11
    Views
    2,467

    Re: what yamaha jet engines in nautica jet rib 10?

    Bringing this back to see if anyone can help with finding the pump wedge mentioned above. Thanks.
  14. Replies
    11
    Views
    2,467

    Re: what yamaha jet engines in nautica jet rib 10?

    I want to get and try a 2 degree up angle pump wedge and see if that helps my problem. I've contacted a couple of pwc performance places and they don't carry one for my pump (which I believe? is...
  15. Replies
    11
    Views
    2,467

    Re: what yamaha jet engines in nautica jet rib 10?

    .....
  16. Replies
    11
    Views
    2,467

    Re: what yamaha jet engines in nautica jet rib 10?

    The motor sounds great and wants to go, but I can't get anywhere near wot. By 3000 and about 25 mph, the thing is plowing to the point where it violently digs in and turns and tries to toss me off....
  17. Replies
    11
    Views
    2,467

    Re: what yamaha jet engines in nautica jet rib 10?

    Picking up this thread again. Boat is all together and running and floating, but have a handling problem. Could someone tell me what yamaha pump would have been on this? Boat had no pump on it when I...
  18. Replies
    6
    Views
    1,365

    Re: impeller rebuild goof opinions needed

    I looked at the impros menu. If I'm reading correct, their worx #3 option for $125 is a full reconditioning including welding?
  19. Replies
    6
    Views
    1,365

    impeller rebuild goof opinions needed

    Need opinions on whether I am right or wrong to be pissed. Sent my solas ka-sc-i out to be serviced. I got the impeller used. It was in a pump that the bearing had gone and 2 blades had been beat up...
  20. Replies
    5
    Views
    1,056

    Re: kawasaki sc and 650 sx-paint or gel coat color

    Thank you. Do you know if there was a paint color code for the factory paint or if there is an aftermarket paint code that is the same (or very close)to the factory .
  21. Replies
    5
    Views
    1,056

    kawasaki sc and 650 sx-paint or gel coat color

    Hi, I own a '90 kawasaki 650 sx stand up and a '91 kawasaki sc (sea couch). I have some chips, scrapes and dings I need to fix on the hulls above the water line. Over the years, I have been told a...
  22. Replies
    3
    Views
    989

    Re: 760- rate of oil from oil injection pump

    Ok. Not running a drill though; this is with motor running at idle. thanks.
  23. Replies
    3
    Views
    989

    760- rate of oil from oil injection pump

    Hi, While running premix in the tank, have been running the 2 oil injection lines to the carbs into a clear water bottle to observe the flow rate. Each line drips one drop every 1 1/2 to 2 seconds....
  24. Re: where to find rubber "boot " for driveshaft end of impeller

    I should mention that my skis are a kaw '91 sc and a '90 650 sx. . My friends is a '88 650 sx.
  25. Replies
    5
    Views
    1,499

    Re: kaw 650- what happens if pump not siliconed

    Wanted to update this thread. Took ski out with no silicone. Don't know why but smooth as glass and no cavitation. Had full power and ran great. Don't understand it but ain't complaining. Job done....
  26. where to find rubber "boot " for driveshaft end of impeller

    Hi, I need the rubber thing shaped like a cone that fits into the end of the impeller and provides a nice taper and fit at the driveshaft.It is not shown on the parts schematic.Could you please tell...
  27. Replies
    5
    Views
    1,499

    kaw 650- what happens if pump not siliconed

    Hi, Working on a friends '88 650 sx. Need to pull and replace pump a couple of times with water tests in between. I'm not going to go through all the crap of siliconing the pump in and then cutting...
  28. Kawasaki 650 - size of oil injection line from pump to carb

    Think that it is 1/8" id. Please confirm. Polyurethane is best type to get? Thanks.
  29. Re: difference between solas ka-sc-A and ka-sc-I impellers

    Thank you both. One follow up question: the rubber boot that goes in the hub of the impeller and seals around the driveshaft is ripped. Where would I buy that piece?
  30. difference between solas ka-sc-A and ka-sc-I impellers

    The "A" looks to have a bigger hub area where the driveshaft connects to the splines. It says "supra" on it but doesn't list variable pitch numbers.

    The "I" has a smaller hub area and says 13-18...
  31. Replies
    4
    Views
    1,735

    Re: stuck impeller/wear ring swollen on 650 pump

    Thank you for response. There is no moving the liner. This is a 30 year old full time salt water pump that is swollen really bad. I plan to destroy the pump housing with the sawzall, it is junk...
  32. Replies
    4
    Views
    1,735

    Re: stuck impeller/wear ring swollen on 650 pump

    Ok, what should I use?
  33. Replies
    4
    Views
    1,735

    stuck impeller/wear ring swollen on 650 pump

    Hi, Read alot of old posts about this but didn't find one that covers my situation. Pump out, impeller shaft out, impeller still stuck REAL tight because of swollen wear ring. Won't budge at all....
  34. Replies
    2
    Views
    1,059

    '91 kawasaki sc full throttle problem weird

    Hi, When I'm on the water and hit throttle for full speed, sometimes I get it and sometimes I don't. Nothing wrong with cable. You can hear that motor just won't turn up. Probably getting about 3/4...
  35. Thread: cdi for '91 sc

    by bbar
    Replies
    3
    Views
    1,276

    Re: cdi for '91 sc

    Picking this thread back up as still having cdi problems. Bought a new aftermarket direct plug in 4 wire cdi. Put it in , no spark. took it out, put my old one back in, ski started right up (but...
  36. Thread: cdi for '91 sc

    by bbar
    Replies
    3
    Views
    1,276

    Re: cdi for '91 sc

    Just sent you a pm. Hope it went through. thanks.
  37. Thread: cdi for '91 sc

    by bbar
    Replies
    3
    Views
    1,276

    cdi for '91 sc

    Hi, the cdi on my '91 kawasaki sc is not working. Motor still runs but can't shut it off. Have done all tests and it is the cdi. Original part number was 21119-3721. Who carries a replacement for...
  38. Thread: cdi for '91 sc

    by bbar
    Replies
    0
    Views
    972

    cdi for '91 sc

    Hi, CDI in my '91 kawasaki sc is not working. Still runs but I can't shut it off.Have done all tests, etc. and it is definately the cdi. Original is part # 21119-3721. It is a 4 wire (2 kill...
  39. Replies
    2
    Views
    1,228

    Re: '91 kawasaki sc lanyard switch/spark question

    ....
  40. Replies
    2
    Views
    1,228

    Re: '91 kawasaki sc lanyard switch/spark question

    ....
  41. Replies
    2
    Views
    1,228

    '91 kawasaki sc lanyard switch/spark question

    Hi, '91 sea couch. I have spark coming and going.Without the lanyard attached,the ski won't crank which is normal. The switch is working correctly for that so the ski cranks.but no spark. But it...
  42. Replies
    0
    Views
    491

    '91 sc oil pump tubing

    Hi, '91 kawasaki sc (sea couch). Need to replace the oil tank to oil pump tubing (yes I am continuing to use the oil pump). Diagram says it is "5.8 x 10.8 x 910" and is discontinued. What size tubing...
  43. Re: '91 Kawasaki sc fuel pick up screens question

    The sc model has no other filters. Unless I install inline filters in the on and reserve line I need the screens. Don't know how long they have been off, but that is probably why I just had to have...
  44. '91 Kawasaki sc fuel pick up screens question

    Pulled the pickups out of my fuel tank in order to clean the tank. Discovered both filter screens laying on the bottom of the tank.

    Were they just pushed on to the tubes? I see no other way they...
  45. Replies
    15
    Views
    3,416

    Re: '91 sc stalling out after flush water turned off

    Hi, Restarting this thread. I did not use couch this past season. Now working on it.Compression is: 150 in forward cylinder; 145 in rear. Engine is factory original stock. Carb is off and going to be...
Results 1 to 45 of 100
Page 1 of 3 1 2 3
Powered by vBadvanced CMPS v4.2.0