pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: hooka-2; Keyword(s):

Page 1 of 40 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    12
    Views
    437

    Re: Purchase with no title....

    A long time ago I contacted Kawasaki in California and all I had to do was send them a pencil tracing of the HIN plate. The apparently checked if it was stolen and sent me a new title in my name....
  2. Replies
    1
    Views
    123

    Re: Pop-off pressure

    It will fall on it face when you try to accelerate if it's too high. It will be rich and stumble if it's too low.
  3. Replies
    24
    Views
    564

    Re: Prop for highly modded 750

    I'm running a 10/18 big hub with a stuffer and a PJS ripturn nozzle and it hooks up great. I was cavitating a little with a 9/17
  4. Replies
    5
    Views
    300

    Re: West coast dual fuel pump

    sent you a PM
  5. Replies
    2
    Views
    297

    Re: X2 with 750 engine

    No you would have to do a bunch of fiberglass work to install the 750 pump on an X2 and it it wouldn't make any difference in performance. Both pumps are 140 mm. The only advantage (if any) would be...
  6. Replies
    5
    Views
    385

    Re: X2 restoration?

    Yup pretty easy swap and well worth it. Same foot print so it bolts right in. You have to use the exhaust manifold from the 650 motor and the intake and carbs from the 750. Use an aftermarket pipe or...
  7. Replies
    10
    Views
    1,538

    Re: X2 dual carb flame arrestors???

    Yes. With 2 left braces almost all cone filters will fit. You still have to modify the oem and the square ocean pros to fit even with the 2 lefts

    I also run a surf brace with the 2 lefts and still...
  8. Replies
    5
    Views
    385

    Re: X2 restoration?

    If it's an old red head motor you may never get the head off even with dynamite. 650 motors are dirt cheap just buy a new one. As a matter of fact I have 2 650 motors that I would let go cheap if...
  9. Kawasaki 750/800 into an aftermarket hull set up for Yamaha. ANYBODY DONE IT?

    Has anyone made a conversion kit to put a 750 or 800 Kawasaki into an aftermarket hull that is set up for a Yamaha 701/760 footprint? how did you do it? Please save the Pro Yamaha/slam Kawasaki ...
  10. Re: MSD flyheel, plate, pickup, coil 650/750 800/? brand new

    would you sell just the plate?
  11. Replies
    0
    Views
    176

    WTB OEM bilge hoses and mount clamp

    I'm starting to put my build together after doing all the body work and re-painting and I find I'm missing the stock bilge hoses and the clamp that mounts the hose to the thru hull bearing. Anybody...
  12. Replies
    9
    Views
    635

    Re: WTB MSD 42351 multi channel brain box

    Found one looking for a spare
  13. Replies
    4
    Views
    254

    Re: WTB short flame arrestors (2)

    Got em thanks
  14. Replies
    4
    Views
    254

    Re: WTB short flame arrestors (2)

    sorry box was full please try again if you attempted contact
  15. Replies
    4
    Views
    254

    Re: WTB short flame arrestors (2)

    Interested what type and how much?
  16. Replies
    4
    Views
    254

    WTB short flame arrestors (2)

    Need a set of short flame arrestors like the Tau Ceti 1 1/2 or 2 inch tall arrestors for my current build. Would consider taller arrestors like Pro K if price is right. Send pic and price shipped...
  17. Replies
    9
    Views
    635

    Re: WTB MSD 42351 multi channel brain box

    Not sure all the differences other than that model has 2 channels and uses the plug in chips. The 42351 is all dip switches and has 3 channels. interested in selling the one you have?
  18. Re: im fixing a freinds stand up. cooling hose broke off can I use the drain line?

    they used to sell a dual cooling kit for the old standups. It was basically a long drill bit and a new tube. I installed a couple of them. Just drill a new hole shove a new tube in it and seal the...
  19. Replies
    26
    Views
    837

    Re: Remove Broken mixture screw from SNB 44

    so it's basically Ausie Ospho
  20. Replies
    9
    Views
    635

    Re: WTB MSD 42351 multi channel brain box

    ttt
  21. Replies
    26
    Views
    837

    Re: Remove Broken mixture screw from SNB 44

    You use an antibiotic to get a screw loose? Never heard of such a thing
  22. Replies
    9
    Views
    635

    Re: WTB MSD 42351 multi channel brain box

    still looking
  23. Replies
    24
    Views
    1,153

    Re: Sxi pro not starting but turning over.

    If you got water in the crankcase you can also try the hot spark plug trick. Heat the end of the spark plug with a propane torch until the tip of the grounding arm glows red, screw it in , crank and...
  24. Replies
    24
    Views
    1,153

    Re: Sxi pro not starting but turning over.

    Sounds like you've been messing with this thing quite a bit. How much fuel have your poured in to the plug holes? and how much fuel has been sucked in the crankcase due to cranking and not starting?...
  25. Replies
    24
    Views
    1,153

    Re: Sxi pro not starting but turning over.

    If you eliminate fuel and compression and have a good blue spark, the only thing left is timing. Did you shear the flywheel key? I have on one occasion found a flywheel that had weak magnets giving a...
  26. Replies
    24
    Views
    1,153

    Re: Sxi pro not starting but turning over.

    around 110 volts or better. Most of the ones I,ve tested lately for are for 650s and run low 100s I would think the 750 puts out at least that much
  27. Replies
    13
    Views
    369

    Re: WTB Mikuni 44 or 38 fuel pump assemblies

    I have no idea. I like a pump on each carb
  28. Replies
    13
    Views
    369

    Re: WTB Mikuni 44 or 38 fuel pump assemblies

    Hey man I appreciate the effort. You definitely tried to help. Thank You. and special thanks to Grump Old Guy he hooked me up.
  29. Replies
    7
    Views
    729

    Grumpy Old Guy is the man

    Don hooked me up with the parts i needed for a great price and then even threw in some extras. What a great guy to talk to. Can't say enough about him. This this the second he came through for me...
  30. Replies
    13
    Views
    369

    Re: WTB Mikuni 44 or 38 fuel pump assemblies

    those are not correct either. Mine have the pulse fitting like the ones in your first pics but do not have a fitting on the block
  31. Replies
    13
    Views
    369

    Re: WTB Mikuni 44 or 38 fuel pump assemblies

    The pump blocks i need do not have an inlet fitting. My inlet and return fittings are both on the carb body.
  32. Replies
    13
    Views
    369

    Re: WTB Mikuni 44 or 38 fuel pump assemblies

    I can't tell in the pic but it looks like only one pump assembly for a triple carb set up? or is there 2 pump assemblies? I can't tell from the pic
  33. Replies
    13
    Views
    369

    WTB Mikuni 44 or 38 fuel pump assemblies

    I need two fuel pump blocks and cover plates to convert SBN 44 carbs from remote fuel pump to integrated fuel pump assemblies. Anybody got some old parts carbs (44 or 38 will work) laying around...
  34. Replies
    5
    Views
    345

    Re: Can you put a 750 in a 650sx

    Not hard at all. Same footprint. Tons of articles on it. Same as doing a 750 swap into an X2
  35. Replies
    24
    Views
    1,153

    Re: Sxi pro not starting but turning over.

    You didn't say, are you getting a nice blue spark? Stators can test good on an ohms test and still be bad. You need to check output with a DVA or peak voltage meter
  36. Replies
    3
    Views
    322

    Re: beach rash on X2 how to fix

    Don't go overboard on repairing the bottom. I've painted several skis that I made the bottom perfect and the first thing I had to do was drag them on to the beach a couple times to scuff them up so...
  37. Replies
    8
    Views
    464

    Re: Kawasaki 650sx won't rev high

    How come they will run fine with the gas cap off then? just saying. The check valve is only there to prevent a fuel spill. PERIOD
  38. Replies
    5
    Views
    354

    Re: Seat Cover Install

    also do yourself a favor:

    1. have a helper to help stretch and hold the material
    2. start from the middle and work out to the ends
  39. Re: Anyone ever flatwater flip an X2 with a modded 650?

    and a 95 pound rider
  40. Replies
    8
    Views
    464

    Re: Kawasaki 650sx won't rev high

    The keihins carbs don't require pressurization like the old sb mikunis did. It sounds like maybe your pop off is too high if it wants to stall off idle that or your low speed jet is too small or...
  41. Replies
    5
    Views
    354

    Re: Seat Cover Install

    I tried using a pneumatic and electric also and found that my manual Powershot from home depot worked the best. You still need to tap some of them in a little with a small hammer but at leas they...
  42. Replies
    10
    Views
    508

    Re: WTB 95 - 96 HX water box for my X2

    I don't know why the post won't link. Google "Poor mans 2 inch exhaust" it comes right up
  43. Replies
    10
    Views
    508

    Re: WTB 95 - 96 HX water box for my X2

    http://http://www.pwctoday.com/showthread.php?t=420269

    I used the one with no fittings on mine
  44. Re: WTB 750 / 800 e-box housings or complete unit

    complete 750 sx box on e-bay right now. Bid is at $75
  45. Replies
    19
    Views
    879

    Re: dual carb tuning

    You are correct. I forgot I cut those off to expose the t-handles. It doesn't effect anything as far a strength. Makes tuning a breeze
Results 1 to 45 of 1776
Page 1 of 40 1 2 3 4
Powered by vBadvanced CMPS v4.2.0