Search Results - PWCToday
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: JasonZE; Keyword(s):

Page 1 of 70 1 2 3 4

Search: Search took 0.26 seconds.

  1. Replies
    0
    Views
    399

    1100 advent wiring diagram?

    Hi, anyone got a copy of the 1100 kawi t3 advent ignition wiring diagram?
    Most is fairly obvious but just want to check on the kill switch as there are a few black with colored trace so need to...
  2. Thread: Salt on engine

    by JasonZE
    Replies
    2
    Views
    1,347

    Re: Salt on engine

    glue up all the holes in the underside of he seat with urethane or similar, seadoo did this from 2015- (didnt drill the holes as opposed to glue but you get the idea)
  3. Replies
    4
    Views
    6,014

    Re: Seadoo rxpx des post replacement

    the correct method is to buy a new dess and new pins and then crimp/solder the pins on and feed into plastic plug housing so its as good as factory.
    the dess from new comes with no plug or terminals...
  4. Replies
    4
    Views
    4,700

    Re: Service supercharger warning

    whoever told you 150 is not the person to be getting advice from 100hrs! the internal ****s are a bit off you plug into them and the service counter and total hour counter can be quite different....
  5. Re: DESS Switch will not shut off 2008 GTI 130

    the post can be replaced and not have to use dealer computer etc as the ke and ecu are programmed the post has no effect on that.
    you can just fit a new post and go. get the new one and use the...
  6. Replies
    13
    Views
    2,085

    Re: SXR 800 2009 >Need help no spark

    ohm test the flywheel pick up sensor from the wiring ontop of the electrical box via the green and blue wires in a 2 pin plug
  7. Replies
    5
    Views
    2,289

    Re: Pressure build up behind dip stick

    you can block off the tops it needs to be open running and closes when the ski rolls over and when shut off.
    in a boat they dont use tops as the likely hood of rolling a boat is slim.
    Open it up...
  8. Thread: Year or motor

    by JasonZE
    Replies
    6
    Views
    1,184

    Re: Year or motor

    just make sure if you rebuild it to the newer spec shaft to use the 3 washers between s/c and block

    Cheers
  9. Replies
    13
    Views
    5,241

    Re: RXT-X collapsed oil filter

    Often water from leaking intercooler leads to that, what max rpm are you seeing
  10. Thread: Year or motor

    by JasonZE
    Replies
    6
    Views
    1,184

    Re: Year or motor

    have a look at the numbers on supercharger the instructions on s/c kit tells you which housing came with no washers.
    if the number is 163 it is the non washer type s/c and if rebuilt with later kit...
  11. Replies
    6
    Views
    2,533

    Re: 2006 GTI SE 130 Issues....

    with all 4tecs grease the drive shaft spline in the prop and make sure the nose rubber boot is ok we are seeing a few aerly skis with stripped spline and usually no or damaged boot and rusted splines
  12. Thread: 04 rxp 215

    by JasonZE
    Replies
    3
    Views
    1,186

    Re: 04 rxp 215

    of course you can make an outlet and block the old outlet off and run a piece of tube from the original exhaust to the new outlet.
    The black plastic muffler/resonator really cuts down the drone but...
  13. Replies
    13
    Views
    3,017

    Re: Jumping RXTX 260 hp

    if jumping big the ibr takes a beating and can break,
    any skis in the surf need regular (every day) engine mount checks as they will break and if not spotted sink the ski.
  14. Replies
    2
    Views
    1,231

    Re: Problem at reducer GTI 130

    obviously you need to make sure they are tight but in saying that I have seen a few leaking there and it doesn't cause an issue and fitting a new reducer doesn't stop it either.
    Its only cooling the...
  15. Re: How do you reset/delete the "wrench" symbol after the 25 hour mark on a 2013 RXP-

    not without a scan tool or dealer buds computer
  16. Replies
    8
    Views
    884

    Re: *the crank coming apart or what?

    looks like you have it all apart so you tell us!

    Certainly looks like crank or little end bearing parts have gone through it I usually see little end failures more often than crank main or big...
  17. Re: STX 15F DIED Just was running fine could not restart dash went dark .

    I was talking about the orange switch in the glove box which can be intermittent did you get the old battery tested?
    Hopefully it was just that but if it does it again you have a starting point.
  18. Re: STX 15F DIED Just was running fine could not restart dash went dark .

    get the battery tested but some (yuasa) etc batteries are absorbed matt type so look dry. You need to get a multi meter or test light and do some testing I have seen the orange ignition switch get...
  19. Replies
    1
    Views
    658

    Re: gtr215 hull damnage

    The hull is only single layer but if under the fuel tank etc there will be foam etc there.
    To roll over is easy i would drain the oil and gas and remove the battery. you can roll on its side and it...
  20. Re: 95 GTX Just revs up when I give it throttle...

    who said it had a carbon seal?
  21. Re: 95 GTX Just revs up when I give it throttle...

    it is cavitation and you need to check for airleaks around the intake area of the jetunit. (assuming prop and wear ring are good) things like driveshaft seal and the glue/sealant around the pump shoe...
  22. Replies
    1
    Views
    2,733

    Re: Seadoo spark overheating at idle!

    have you had a damaged wear ring? if so check the plastic tube that feeds water from the jetunit to the hull this can get damaged and if its leaking will not flow enough at low revs.
  23. Replies
    27
    Views
    29,525

    Re: My 2015 SeaDoo Spark Review

    I highly doubt that and looks like graze marks above the damage, I have had 2 that had major teebone impact with another ski and were nowhere near that bad just a localized hole/cracking and in the...
  24. Thread: 2015 rxtx

    by JasonZE
    Replies
    8
    Views
    1,477

    Re: 2015 rxtx

    as far a I know its the newer design hull (white double skin) as opposed to the single skin (yellow/tan) coloured hulls with ribs etc they ran in the s3 from 09 to end of 15.
  25. Replies
    11
    Views
    1,608

    Re: GTI-LE Does not go over 35

    we need to know what rpm you are reaching,
  26. Thread: 2015 rxtx

    by JasonZE
    Replies
    8
    Views
    1,477

    Re: 2015 rxtx

    as the gps is the speedo now there's no sensor at the back to show water temp. just stick your toe in thats accurate enough
  27. Replies
    9
    Views
    4,016

    Re: 2002 gtx 4 tec code P0116 and P0118 advice

    is the rideplate getting hot indicating coolant is actually flowing? and thermostat operation. How did you know its 93-97 are you sure its not hotter?
    If temps are fine then a wiring issue will be...
  28. Thread: 2015 rxtx

    by JasonZE
    Replies
    8
    Views
    1,477

    Re: 2015 rxtx

    Congrats on the new ride, I like both but the red is nice I just sold our last one and have the new colour arriving next week so hope our customers like it as no other option.
    I rode the new color...
  29. Replies
    5
    Views
    1,716

    Re: 2008 GTI 130 turning over real slow.

    a few things possible, common stuff battery or cables, bad stuff (since it did it running) are impellor not done up tight and coming loose and driveshaft pushing hard in the back of the motor. this...
  30. Replies
    8
    Views
    1,911

    Re: What would happen if I ran it like this?

    I too would run it but grind that section out ( a nice window type cutout with chamfered edges like factory cylinders often have) this way the skirt is still supported and the sleeve has enough...
  31. Replies
    1
    Views
    1,010

    Re: Rxt 255 2008 overheating

    even running on the hose you can feel if the water is circulating through the ride plate by touching it. And the 1 hose going from the thermostat housing should be hot and the one returning from the...
  32. Replies
    1
    Views
    916

    Re: Rxt 255 2008 overheating

    might have blown the head gasket which caused the thermostat to blow out in the first place, Im trying to think how not running a thermostat will work as it diverts the water around the block and oil...
  33. Replies
    4
    Views
    1,510

    Re: 2006 Sea Doo GTX Vibration Problems

    the older 2 strokes bend drive shafts but I have never seen a 4 stroke bent (stripped yes) in 10 years working full time on them.
  34. Replies
    6
    Views
    1,058

    Re: 787 Flame Arrestor Gasket???

    you dont need any sealant/glue on them at all.
  35. Replies
    4
    Views
    1,510

    Re: 2006 Sea Doo GTX Vibration Problems

    should be straight forward there arent really any traps to fall inot just make sure the 3 rubber seals between the jetunit and hull dont drop out
    Im sure the prop with have some damage front or rear...
  36. Replies
    36
    Views
    8,627

    Re: Need advice on buying a Spark

    where I am we got the Sparks when they were first released, as it was coming into our summer USA winter. Much like the US guys stocks were limited first season but we still sold over 40 and have been...
  37. Replies
    36
    Views
    8,627

    Re: Need advice on buying a Spark

    Whats to laugh about Im a seadoo dealer and sold close to 90 sparks over 2 summers, maybe you should stay in the yamaha section?
  38. Replies
    6
    Views
    795

    Re: Jet pump cone oring

    thats ok not until late 90's you can get caught out on the pusher setup
  39. Replies
    36
    Views
    8,627

    Re: Need advice on buying a Spark

    i would go a 90hp and leave it stock
  40. Replies
    6
    Views
    795

    Re: Jet pump cone oring

    what year/model as depending on that there certain things to do when putting the cone on relating to the spring loaded pusher inside the cone.
    you may need a new o ring as when they are swollen they...
  41. Replies
    6
    Views
    1,058

    Re: 787 Flame Arrestor Gasket???

    they dont run a gasket on there for any of the single or dual carb models
  42. Re: 2003 Sea Doo GTI LE - trouble starting, battery is good, starter relay is good

    if all the main battery cables and terminal ends are good then the starter is the likely cause and not uncommon. they are not that hard to remove either. best to do it soon or you will burn the...
  43. Replies
    36
    Views
    8,627

    Re: Need advice on buying a Spark

    I disagree with comments about it being a turd unmodified, I have ridden many and sold over 80 Sparks and no complaints about performance from surf or flat water riders and families towing biscuits...
  44. Re: Can't remove O-Ring from Driveshaft on Seadoo XP

    with rust they can be seized solid at times, if replacing the floating ring and carbon seal you may have to cut it off otherwise in the past i have lifted the engine up and forward to get shaft out....
  45. Re: ultra 150 goes good for 1-2 laps then wont rev over 4000

    Ahhhhhh yes I forgot although they didnt come out that well you get the idea basically the inner ballooned up and stayed there while the outside of the hose looked ok

    here we are!
    ...
Results 1 to 45 of 3141
Page 1 of 70 1 2 3 4
Powered by vBadvanced CMPS v4.2.0