pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: hemmjo; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Thread: Girls and ski,s

    by hemmjo
    Replies
    2,879
    Views
    620,903

    Re: Girls and ski,s

    She is a very attractive woman. And I really like that she is actually riding a ski. But DAMN.... that is some BLUE water!!!!!! Where is that??
  2. Replies
    7
    Views
    339

    Re: 2000 RX 951 oil issue and prop question

    Yes, it is possible the oil leaked into the cylinder from the pump over time. That is why I suggested you try the setup as I outlined. To see if oil leaks through the pump. If this is the cause, a...
  3. Replies
    7
    Views
    339

    Re: 2000 RX 951 oil issue and prop question

    I will take a long shot guess at this. A cup is a lot of oil to fit into the crank case. There are only a couple of ways the oil could have gotten in there, either someone put it in there or it...
  4. Thread: Girls and ski,s

    by hemmjo
    Replies
    2,879
    Views
    620,903

    Re: Girls and ski,s

    Oh, I thought he meant her fingernails were fake...
  5. Thread: Girls and ski,s

    by hemmjo
    Replies
    2,879
    Views
    620,903

    Re: Girls and ski,s

    you are doing a fine job LinkMan
  6. Thread: reverse kit

    by hemmjo
    Replies
    2
    Views
    428

    Re: reverse kit

    This is just my opinion...

    Have you ever ridden one with a reverser on it? I am not at all impressed with them on the Sharks I have. I have also driven several jet boats with them. While they...
  7. Replies
    5
    Views
    317

    Re: Running Carbs Dry For The Winter

    There are mixed reasons both to run dry and to not run dry. Ethanol is NOT GOOD for metal specifically brass and aluminum in carbs. It is corrosive, attracts water, and leaves behind nasty deposits...
  8. Replies
    2
    Views
    1,199

    Re: 770 Crank Bearing retaining pins

    Thanks for your input, I believe you are correct Kyle. It appears that there was a design change what was not updated in the service manual. It is interesting to also note that the the Artic Cat...
  9. Replies
    6
    Views
    362

    Re: 62t crank alignment pins

    If you have a drill press, find a piece of wood the is sturdy and large enough to hold your case. Like a 2 x 10 or something. Then clamp the wood to the drill press table so the case is completely...
  10. Replies
    6
    Views
    362

    Re: 62t crank alignment pins

    Ah, I feel your pain!! Those pins get pushed flush like that for two possible reasons. The first is whoever installed the crank did not get the pins lined up with the holes in the bearings. Then...
  11. Replies
    5
    Views
    366

    Re: Trailer tires - help needed please!

    Here is a ShoreLand'r brochure, shows the standard tire sizes.533304

    Good Luck
  12. Replies
    8
    Views
    450

    Re: XP-S Anti-Corrosive Lubricant

    Not any cheaper, but seems to work.. http://www.corrosionx.com/corrosionx.html
  13. Thread: Girls and ski,s

    by hemmjo
    Replies
    2,879
    Views
    620,903

    Re: Girls and ski,s

    let me help you out Linkman.
    532954
  14. Replies
    7
    Views
    534

    Re: Flood Damage Skis

    I have no experience with a flood damaged ski, but I imagine the damage is similar to a sunken ski. I have repaired a couple of sunken outboard motors. One had been submerged for a couple of months,...
  15. Replies
    4
    Views
    538

    Re: recover gas from 2005 VX100 deluxe

    Not sure how the fuel systems are plumbed on new models. On my old ones, I disconnect the line between the tank and the filter, connect a longer line running to a can on the ground and siphon it out...
  16. Replies
    71
    Views
    7,872

    Re: ts77r hole in piston

    did you look at the 900L set up? Sounds like that is similar to what you have. You might need to play with a restrictor in the T if you add one, so you get flow to both places
  17. Replies
    3
    Views
    156

    Re: WANTED 650 4 wire TS stator

    They are not really too hard to rewind, if you have a bad one and can not find a good one. jus' sayin'
  18. Thread: Girls and ski,s

    by hemmjo
    Replies
    2,879
    Views
    620,903

    Re: Girls and ski,s

    just so you know.There really is a ski in #2660
    532416
  19. Replies
    71
    Views
    7,872

    Re: ts77r hole in piston

    The diagrams above are for TS770, 770L, 770R from the 1999 service manual.
    Here are the other diagrams included in that manual; 900L, 1100R and 1100Li.
    Each on is a bit different, maybe one is...
  20. Replies
    71
    Views
    7,872

    Re: ts77r hole in piston

    Here are the diagrams from a 1999. Mine is a 98 TSL. Notice the anti-siphon valve I have sketched on that page. It is in the boat, but not indicated on that diagram.532374532375532376532377
    ...
  21. Thread: Girls and ski,s

    by hemmjo
    Replies
    2,879
    Views
    620,903

    Re: Girls and ski,s

    I am just disappointed I am not there taking the photo!!
  22. Replies
    3
    Views
    342

    Re: Connecting wires - regular wire crimp?

    If you want to ride today, you can use crimp connectors for short term. But you should as soon as possible make proper solder connections. Then coat with Liquid Electrical tape. Something like this...
  23. Replies
    11
    Views
    584

    Re: Valve shim measuring onfx140

    ...not sure what that post above says....

    I have not worked on your specific engine. Back in the 60's, (I have been at this a long time) Homelite introduced the first 4 cycle outboard. They...
  24. Replies
    28
    Views
    837

    Re: top end rebuild...gasket question

    You really need to do this spin test with VERY little or no oil. The oil does is job and fills the small imperfections in the bearings, as it should. Spinning the bearing by hand, with no real load,...
  25. Replies
    10
    Views
    625

    Re: JS550 Piston Damage

    From the looks of the piston, I have to assume that the head has a lot of matching dents. Something has been sucked into the engine or come loose from inside it. The consistent size and shape of...
  26. Replies
    28
    Views
    837

    Re: top end rebuild...gasket question

    If you intend to ride for very long after you put it back together then you need all new bearings. I know you said you don't have much money. I can certainly relate to that!! When that noise...
  27. Thread: bendix removal

    by hemmjo
    Replies
    18
    Views
    2,518

    Re: bendix removal

    I put a piece of clear fuel line on my 770's then ran it to a fitting I installed on the bottom of the cover. I can now see if there is any fluid, either water from a crash, or oil from a leaking...
  28. Replies
    1
    Views
    268

    Re: 1996 speedster no spark on one engine

    I am thinking splicing the rev limiters would be a bad idea. Cant say for sure but I am thinking the lmiter counts pulses, and each engine would be sending pulses, so they may only run 1/2 speed...
  29. Replies
    5
    Views
    295

    Re: Stripped cylinder stud hole.

    check with your local NAPA auto parts store..
  30. Replies
    8
    Views
    338

    Re: 750 Bendix washer?

    if you know someone with a lathe they can make one in about 10 minutes
  31. Replies
    7
    Views
    496

    Re: Ring compressors

    ON 2 stroke I always use the model shown above. It is much easier making sure the ring ends are positioned correctly over the locating pins with that model.

    When I need a metal compressor, I use...
  32. Thread: tuning question

    by hemmjo
    Replies
    5
    Views
    463

    Re: tuning question

    I would try the front one, and see if it helps. Be sure you remember how much you turn it. If it helps, do the rear the same amount when you get off the water.

    But remember, a 2 cylinder 2-stroke...
  33. Re: Having to use lighter springs for correct pop off.??????

    I have not done a lot of these, but 75psi seems huge? Just curious what is this for?

    It would stay open if you could supply a constant supply of pressure at the PSI required to pop-off, but as...
  34. Re: New to stand ups, need to change charge coil in JS550

    Sounds like a good time to get the kids involved with repair of the toy they enjoy so much!!! When you are finished with it for the summer, get after it.

    I feel your pain in regard to hands not...
  35. Re: digital voltmeter won't read battery voltage js550

    I have never seen this happen, so what follows is just a shot in the dark...

    Is the meter is reading OK above idle?

    I wonder if it is possible.... when at idle, alternator output is so low...
  36. Replies
    71
    Views
    7,872

    Re: ts77r hole in piston

    If I was you, I would disconnect the drive shaft and run it. That "tinny rattle" sound could be in the pump. Hoping you have not pulled the engine yet.
  37. Thread: Hull damage

    by hemmjo
    Replies
    4
    Views
    553

    Re: Hull damage

    Here is a link to the same info that was in the book.. very good info..

    http://epoxyworks.com/index.php/common-errors-in-fiberglass-repair/
  38. Thread: Hull damage

    by hemmjo
    Replies
    4
    Views
    553

    Re: Hull damage

    There is lots of information online regarding fiberglass repair. I have done lots of repairs of larger boats, a couple of rowing shells, as well as fabrication of fiberglass parts for various...
  39. Thread: Girls and ski,s

    by hemmjo
    Replies
    2,879
    Views
    620,903

    Re: Girls and ski,s

    red ski, blue ocean, pink girl..528551
  40. Thread: oiling help

    by hemmjo
    Replies
    5
    Views
    308

    Re: oiling help

    If your pump is mixing oil at a ratio of 40-1, and you burn 40 gallons of fuel, you should use 1 gallon of oil. Not sure how much fuel you put in for each fill up, but if we assume you were not...
  41. Thread: Deal or no deal

    by hemmjo
    Replies
    30
    Views
    2,882

    Re: Deal or no deal

    I have a 99 service manual. So far everything in it has been the same for my '98 770L.

    Here is the wiring for the 1999, TS1100R. The lettering is tiny in the manual, I can barely read it directly...
  42. Re: where can i get aa brush kit for a goki starter

    Good to know!!!! Too many techs only know what is in the parts books. They can't to anything without a make and model number. You need to find someone who has been around the block a few times and...
  43. Replies
    24
    Views
    10,359

    Re: Easy Leak Down Tester....

    Actually, the crankcase runs under both vacuum and pressure. So it would not be bad to test it both ways. As mentioned before the pressure test allows you to see bubbles to find the leak.
  44. Replies
    3
    Views
    328

    Re: Pulse nipple too deep into case?

    If I understand correctly, you enlarged the hole for the pulse nipple, using a drill, and you think you may have hit the reed, and damaged it.

    Personally, with what you have said, I would not...
  45. Replies
    6
    Views
    350

    Re: Fuel System HELP!!

    Wondering WHY did you have to rebuild the top end? Did you find and correct the problem that made that necessary?

    You may have melted a piston. Not sure what your specs are supposed to be, but it...
Results 1 to 45 of 316
Page 1 of 8 1 2 3 4
Powered by vBadvanced CMPS v4.2.0