Search:

I have your bed plates , couplers , mid shaft , and lx skinny chamber exhaust , all from a wave runner lx 650 if needed , 6R7 stuff

Found

Any more out there ?

I’ve never seen twin bilge hookups
Usually on a kawi only one that’s the odd thing
Should still work for my application
Pm me your paypal
If 140 pump it will work
Thanks for pics

10 mm socket
6 mm bolt
140 mm pump ?
115mm bolt center like pic ? 564392

What size are the bolts that hold it to pump ? 6 or 8 mm , 140 mm pump or 148 mm pump ?

Where is your starting point , hydro locked and rusted ? Or good core , or no engine at all ?

DI or carb ?

White or silver cylinder ?

That will work , take off and post a pic off the larger hole , pump side , then how much ?

Bump

Still need ?

Had two with tps out of range and pressure sensor out of range
Maintanence light on
Those two connectors on those sensors were switched
They will connect either way
Try switching them , clear...

Is this a new to you ski ?
Inherited problem with purchase ?
Had someone rebuilt top end or engine before you got it ?

I can check for ya

Yep

Just trying to help out a homie in need

Bump

Post pic here , Rowlandaud , of part I’m lookin for , then will get back to you , your English is getting better

She was always there with sand crab , region 1

Looked , only have a stock 44 manifold , Scott Clough Racing , scr was your 440SS guy in the day , just ground out and polished , on my 440SS , scr cylinder , either ran a buckshot 44 or a SBN 46...

Need a stx 900 pump reduction nozzle , PayPal ready

Have a GRS 44 bn single that will fit on stock kawi 44 manifold , and stock manifolds if necessary , might have a SCR modified stock kawi manifold here too

I’ll be back in Lancaster Cali after holidays , to finish selling last house , can do work on yours if wanted , will be transporting my mate to Idaho in March
You need a certain reduction nozzle...

You also have to fix pump problems to make it work , yes been tested , 1100s way more impressive , but it was no slouch

Bump

I have 1 more , sold the first two , lmk

564204564205Better pics

Would have to disassemble
Custom U tubes bent @ muffler shop then off to powder coating for box hookups
The exhaust hose to rear is a modified wr500 rear hose cut to fit
Fitting the pipe takes a...

Bump , still need

564189564191564192564193
750 BP 192* stock limited set up , dual 44 Mikunis , Coffman WR3 pipe , PJS tall perch three bolt manifold , stock modified and fitted water box , custom e box mounting...

564188
cherry , complete , if you need one can’t find em , 20$ shipped

Complete stock 1100 kawi pipes F/S , no cracked manifolds , 275$ shipped , unmolested , stock

Yes 10 mm
Most if not all aftermarket finger throttles are 10 mm
Adaptors reduce to 6 mm or 8 mm
The 8 mm is for SXRs

10/4 , I’ll dig them out on my end too

Got a couple , not sure if early type , what are your wire colors , blue , black , black red , black yellow ?

That one is different , fits a zxi 750 in your pic
Answer to question
Have another almost complete 800 sxr pipe just need headpipe to make complete , or will sell the three pieces I have for a...

Need a good stock 750/800 headpipe for exhaust system
from manifold to first chamber section , PayPal ready , can post pic of part if your not sure

175$ plus pp fees or as a friend , shipped

564135564136
stock SXR complete exhaust F/S , one left

You selling it ?

Found

Split cases to crank , check rods and mains bearings , if no noise , rings , seals gaskets , done , onto carbs , add water

Yes sir it is , pm sent

Watch “ randygross65 “ same scammer , different name

R&D , west coast , mariner , BCW , any will work fine , PayPal ready