Search Results - PWCToday
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: deanobaby; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    2,113

    Re: 900 zxi weak spark some times no spark

    up date

    there are 4 wires going into the ignition switch the multi plug is under the dash / and under the handle bars the plug is hidden inside a big rubber sleave that seals the outer and...
  2. Replies
    5
    Views
    2,113

    Re: 900 zxi weak spark some times no spark

    update and found problem \

    me and the old man did a Continuity test on some wires we found that the ignition switch the one that needs to be turned with the key was acting up

    we cut the wires...
  3. Replies
    5
    Views
    2,113

    Re: 900 zxi weak spark some times no spark

    thanks linkman

    I have cleaned stop start

    I forgot to mention in my first post the engine started good last week I did a compression check and I have just finished a top end rebuild i...
  4. Replies
    5
    Views
    2,113

    900 zxi weak spark some times no spark

    g day all been a long time since I have been on the forum

    recently I have tried to start my 900 zxi it did try and fire up but then died ..I now have no spark I have changed the plugs and cleaned...
  5. Replies
    4
    Views
    595

    Re: keihin cdkII 900 and 1100 carbs same?

    is that inside diameter im sure its different but can still bolt on ...i need to know also wanting to do the same and is it worth it ..but the 1100 has the acceleration pump and different size jets
  6. Replies
    4
    Views
    595

    Re: keihin cdkII 900 and 1100 carbs same?

    different hopefully some can chime in on the 1100 but im sure that jets will be different as well as the 1100 runs another pump as well as diameter in size ..but it can be done
  7. Replies
    5
    Views
    902

    Re: 900 zxi impellor probloms

    i was just having a joke... the forum is very helpfull

    deano
  8. Replies
    5
    Views
    902

    Re: 900 zxi impellor probloms

    i replaced the centre bearing and seals as i thought it was that first .....but noticed i wasnt getting full splines into the impeller ..some splines where still shown coming from impeller as if the...
  9. Replies
    5
    Views
    902

    Re: 900 zxi impellor probloms

    i thought we had gurus on here ??

    but worked it out on my own

    the bed plate on the bottom of the engine can be reversed

    900 bed plate the wrong way
    ...
  10. Replies
    5
    Views
    902

    900 zxi impellor probloms

    ever since i purchased my 900 2nd hand i have noticed that i have allot of impellor probloms

    i have changed from skat trak /solas now i have a nujet

    only to notice when installed all 3...
  11. Replies
    3
    Views
    820

    Re: Zxi gasket question.

    there a crush gasket when there tightend up the crush part is the seal basically use once item ..next time you remove they will be flat
  12. Thread: ZXI Heads

    by deanobaby
    Replies
    1
    Views
    417

    Re: ZXI Heads

    mainly the prices

    what are you looking at and whats your compression stock
  13. Replies
    0
    Views
    1,121

    cleaned up my motor 900 zxi

    i needed to replace the bearings in my prop shaft holder so i thought i would clean her up at the same time
    http://i1149.photobucket.com/albums/o582/deanoobaby/P3190152_zpsc7a619e7.jpg

    the...
  14. Replies
    6
    Views
    923

    Re: nujet 5.0 or 5.5

    i have a solas and skat trak both at 16.21 pitch

    my scat trak is the swirl but worn clearence is at .5 also the splines spun inside its housing

    my solas is a stocker and 2nd hand clearence is...
  15. Replies
    6
    Views
    923

    Re: nujet 5.0 or 5.5

    i was looking for a bit more top speed my other impellers and wearing are worn im pushing 51 /52 mph on gps

    i also do all my riding on the ocean not all the time it flat water
  16. Replies
    6
    Views
    923

    Re: nujet 5.0 or 5.5

    the only thing stock are carbs and pipe i have a cool head that im running 160 psi

    will the 5.0 still be recomended
  17. Replies
    6
    Views
    923

    nujet 5.0 or 5.5

    looking at purchasing either impeller for a 900 zxi

    which one would be better

    thanks
  18. Replies
    4
    Views
    1,217

    Re: looking for a good impellor 900 zxi

    im very intrested ...im sure i have the 900 set up i will measure tonight after work
  19. Replies
    4
    Views
    1,217

    Re: looking for a good impellor 900 zxi

    when i purchased the ski it had the swirl allready installed ..i also got a box of spare parts the spare impeller he gave me looks to be the standard impeller looks like both impellers have seen...
  20. Replies
    4
    Views
    1,217

    looking for a good impellor 900 zxi

    just looking for advise on pitch and brand of an impellor

    i currently used a skat track 16 21 swirl that was installed when i got the ski

    i have a solas 16 21 2nd hand installed now

    whats...
  21. Replies
    8
    Views
    1,509

    Re: Crank seal in wrong direction?

    not to sure what motor we are talking about... but just checked my zxi manual which is also a 2 stroke

    the double lip seal is on the coupling side ...which kinds of makes sense stops hull water...
  22. Replies
    2
    Views
    996

    Re: Piston ring end gap

    http://www.wiseco.com/PDFs/Manuals/RingEndGap.pdf
  23. 900 zxi impeller slippage with a skatrak swirl

    hey all noticed my 900 was slipping intermittent it wouldnt slip all the time but when it did it was bad and allways slipped on take off or hole shot

    i measured the distance between the wear ring...
  24. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    im using 32 domes but my compression is only at 160 /157 and 157psi i wont need racing fuel just yet
  25. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    i also learned some thing new i called into my local jetski garage they reckon the same thing on what you say ....i got home pulled my head gasket compression is now at 160 on the number 3 cylinder...
  26. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    what i ment was that when i was tuning my ski ...if i was idling for long periods ie coming in and out the mariner due to no wake zones when i went to snap the throttle it would want to rev but...
  27. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    i you where to make an oring put it on the top im not to sure if silicon will work but it wont melt

    also try this place ask them if they have the oring kit
    ...
  28. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    forgot to add that the old washers will work fine ..if you dont use washers then torque the nuts down you will tighten the nuts and stretch the studs or even snap the studs
  29. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    hey lordx hows things

    first there should be a rubber ring on both bottom of the basplate and the lid of the head also there should be rubber rings around the domes and they appear to be there in...
  30. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    i forgot to add be carefull when opening the package the domes can fall out when turned up the correct way ...this makes it a bit harder to install ......

    fit the head in stages when installing...
  31. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    when you get the head you will see what i mean not untill the bolts are tight then the head is assembled

    the stock flame arrester fits strait on you may need a spacer for the bolts that screw the...
  32. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    the head should arrive in parts ....first place the head gaskit ontop of the engine the domes will only fit one way as there is a key way locator for them ....the domes will fit into the bottom...
  33. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    the domes will be stamped on the side ie .....# 32/or #30 basically the smaller the number the higher the compression ...i purchased my head gaskit off ebay ....dont worry about over heating with...
  34. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    same head as mine ...mine has the #32 domes ...do a compression test before and after

    try and find out what domes comes with the head you will need a new head gasket and bolt on and play

    when...
  35. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    i run premix on my 900 and ran 120 psi on a stock head i then put a cool head on with 32 domes compression is now at 145 across all 3 never had any failures ...the higher compression does wake the...
  36. Re: Possible OverHeating / Water pisser on a 750sxi question

    have a look at my problom when i was over heating .... http://www.pwctoday.com/showthread.php?t=395672

    if you have no split hoses then there is a blockage maybe in some water gallerys /block...
  37. Re: 1995 Kawasaki 900 ZXI - Issues and Upgrade possibilities?

    purchase a manual do the carbs your self ....if your carbs are pro done they will use a flow meter .not many use it basically they read out the manual

    if you want and when i get some time i cam...
  38. Replies
    26
    Views
    4,273

    Re: F-12x Replacement Turbo

    hear we go another turbo topic ,,,,,,,,i just have to ask do honda have the butterfly that opens and closes inside the inlet manifold

    to snap turbo shafts is that your turbo is under presure when...
  39. Replies
    25
    Views
    4,021

    Re: Oil in Pressure Side of Turbo

    ps i found this how a turbo works please watch

    http://www.youtube.com/watch?v=vGhlgphrBxA
  40. Replies
    25
    Views
    4,021

    Re: Oil in Pressure Side of Turbo

    are you f king with me LOL

    no it wasnt my intention i just googled it and funny enough it was on the top of my page ...as he was changing the oil seal NOT BOOST SEAL


    some need to learn how...
  41. Replies
    25
    Views
    4,021

    Re: Oil in Pressure Side of Turbo

    also come to think about it ....any one hear ever ran 2 stroke surely every one or infact any inclosed engine running inside of a hull a small exhaust leak will make the engine suffer correct
    ...
  42. Replies
    25
    Views
    4,021

    Re: Oil in Pressure Side of Turbo

    hi yes very interesting as i actually work on these at work on some globe trotters

    no matter how the turbine spins it neads oil ....im not here as a challenge on who is best ...infact i no...
  43. Replies
    25
    Views
    4,021

    Re: Oil in Pressure Side of Turbo

    #1 ball bearing solid bearing can be used gas or diesel ...ball bearing is more Efficient

    #2 A/r ratios is mixture basically when i change a turbo the mixture needs to be set incase of an over...
  44. Replies
    25
    Views
    4,021

    Re: Oil in Pressure Side of Turbo

    so whats different between turbos to a gas engine and a diesel engine turbo
  45. Replies
    25
    Views
    4,021

    Re: Oil in Pressure Side of Turbo

    yeah your right it might be a honda thing

    but a turbo is just a compressor mate ....still runs on the same factors

    at least i wont be purchasing a honda any time soon LOL
Results 1 to 45 of 136
Page 1 of 4 1 2 3 4
Powered by vBadvanced CMPS v4.2.0