Search Results - PWCToday
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: john zigler; Keyword(s):

Page 1 of 209 1 2 3 4

Search: Search took 0.51 seconds.

  1. Replies
    2
    Views
    240

    Re: Water pump working??

    Engine cooling water comes from the jet pump pressure. There is no "water pump"
  2. Replies
    3
    Views
    177

    Re: Does Yamaha use a wear ring?

    I always strongly suggest getting a shop manual for your machine, it will give you all the specs, and needed steps to do all service repairs.
  3. Replies
    3
    Views
    177

    Re: Does Yamaha use a wear ring?

    Yes.

    Basically all PWC jet pumps have the same components. Pump stator vein section, impeller, wear ring, reduction nozzle.

    Sounds like you are experiencing cavitation. Cavitation can come...
  4. Re: 1998 Yamaha WaveRunner GP1200W is NOT turning over......

    If you do it your self, we sell kits, $55ea (Genuine Mikuni) Needle and seats are $24 ea. If you pay a shop, it will depend on their labor rate per hour. It take me aprox 1 hour per carb to...
  5. Re: 1998 Yamaha GP 1200 Fuel Filter Replacement Question

    Loosen the gas cap to relieve pressure, turn fuel off. You WILL Spill a small amount of fuel when changing. I put a rag/towel down in the hull to absorb spills. Leave you seat off for a while to let...
  6. Replies
    5
    Views
    252

    Re: Umi bearing kit

    I see your order today, thanks Dave. Your bearings will ship today, look for an email from Fed Ex With tracking.

    John
  7. Replies
    5
    Views
    252

    Re: Umi bearing kit

    If you order from the site, the kit will ship Monday, Fed Ex One rate, 2nd day air shipping ($12) so you will get it Weds this week, 10/14

    John
  8. Replies
    11
    Views
    603

    Re: 550 FUN build. Options hmm

    It is possible to make very good power with a Kawi down low.....
  9. Replies
    5
    Views
    252

    Re: Umi bearing kit

    Yes - https://www.watcon.com/handling/umi/umi-rebuild
  10. Re: 1998 Yamaha WaveRunner GP1200W is NOT turning over......

    For an engine to run, you need spark, fuel, and compression. You need to determine what is missing from this equation, and trouble shoot from there....

    Check compression, test spark with spark...
  11. Replies
    3
    Views
    383

    Re: Non Running Jet ski

    I have a Square nose SJ, with 701 61x single carb (Complete engine runs good)

    Ski needs assembly, but is all there.

    Will include a stainless impeller, new hood seal, new aftermarket deep scoop...
  12. Replies
    3
    Views
    592

    Re: WTB Aftermarket 701 Hull

    Sorry, I do not do PM's here....
  13. Replies
    3
    Views
    592

    Re: WTB Aftermarket 701 Hull

    I have EME Roid carbon mix hulls here in stock, would make you a good deal.... I am in Janesville 53545 Give me a call at the shop to discuss, cash price.

    https://www.watcon.com/body-hull/eme
    ...
  14. Replies
    12
    Views
    553

    Re: Blew exhaust rubber coupler

    You have the ski right? Just measure the OD of the pipe and or water box, and the length needed to connect the two.
  15. Replies
    2
    Views
    256

    Re: 650sx cooling question

    Looks like you have a stock manifold, and head pipe with just a PJS chamber.

    The way you have it plumbed will work, but honestly you are actually adding more water at the stinger than there was...
  16. Replies
    12
    Views
    553

    Re: Blew exhaust rubber coupler

    Going by my memory, your diagram looks to be correct.

    Water is injected in the head pipe to the inner exhaust. THIS is what keeps your couplers, and rubber hoses cool.
  17. Re: 98 Sea Doo GTX Limited High RPMs out of the water, Low RPMs in the water

    I am going to guess, standard SeaDoo grey fuel lines breaking down, carbs gummed up, running lean.

    Go through the fuel system completely, replace ALL lines, fuel select, rebuild carbs, and fuel...
  18. Re: kawasaki x2 with tnt pipe. need waterbox

    Johnny, how do they sound? I have been thinking of having Tony make me some to have on hand here. I am just afraid they will be loud?
  19. Replies
    2
    Views
    278

    Re: 750 ss xi Coffman exh cooling

    Dual cooling from the pump = two lines should come into the manifold. You will then have two lines out from the head. One will feed the pipe, and the 2nd can go straight overboard to a water by pass...
  20. Replies
    12
    Views
    553

    Re: Blew exhaust rubber coupler

    Running on the hose is not always an accurate test.

    I suggest pulling ALL small hoses, and blow out with the air compressor both ways.

    We also pull all the brass fittings, and inspect. I...
  21. Replies
    12
    Views
    553

    Re: Blew exhaust rubber coupler

    This usually happens from lack of water. IE you probably have some sand, or blockage in your exh somewhere, the pipe got hot, and blew the coupler.

    Go over all fittings on your pipe / cooling...
  22. Replies
    11
    Views
    603

    Re: 550 FUN build. Options hmm

    It is just the whole thing. Rhass Parts were not the best fitment, had to modify almost everything to get it to work. Pipe hit the e-box, etc.
  23. Replies
    11
    Views
    603

    Re: 550 FUN build. Options hmm

    I'd stick with a Kawi engine. The Yamaha conversions I have seen were poor fit / alignment, and just a pain in the a..
  24. Replies
    2
    Views
    315

    Re: Sea Doo HX water box

    Not a HX water box, but just a FYI - We have 2" X2 exhaust outlets, that you will need (Unless you are doing a rear exit conversion) to match your 2" HX water box.

    ...
  25. Re: Kawasaki SXR 800 Starts without lanyard and stop button does not work

    This or the stop switch. (Which he has already tested)

    Bluemoon, it sounds like you have gone over everything else. It almost has to be in the wiring.
  26. Replies
    2
    Views
    534

    Re: When to Replace Throttle Cable?

    You can just disconnect the cable at the throttle, and see if it is better. You should be able to pull the ball with your fingers.

    Sometimes if the cable is bound up, or twisted it can cause them...
  27. Replies
    9
    Views
    398

    Re: Crankshaft Rust Question

    That's a lot of rust. I promise, the bearings would have rust as well, are pitted and bad.

    I would NOT run that crank.
  28. Replies
    12
    Views
    614

    Re: Pulled pump cone. Only water inside

    I would fully disassemble, and inspect. On occasion I have seen there is enough oil coating the bearings tat they do not rust, and are fine.

    As said, leak down test upon assembly is very...
  29. Replies
    4
    Views
    356

    Re: WTB solas impeller for 2004 gtx 185

    New Solas in stock here, $280 + ship

    https://www.watcon.com/impeller-solas-concord-sr-cd-12-20-sea-doo-gtx-4-tech-sc?filter_name=gtx&filter_category_id=132
  30. Re: SXR 1100 won't start without fuel in carb

    Hard to say for sure, but you have a fuel issue.

    Either dirty carbs (Still?) Fuel pump, fuel pick up, fuel select switch, fuel filter, ect.

    When your "mechanic" cleaned the carbs did he...
  31. Replies
    6
    Views
    460

    Re: Need help with winterizing GTX DI

    You can add antifreeze right at the flush port at the rear.

    I screw a short (18" or so) hose here, and first blow with the air compressor while the ski is running to get as much water out as...
  32. Replies
    21
    Views
    776

    Re: 1995 Wave Venture 700 guidance

    Springs come in different spring rates, and will affect the tune of your carb / pop off. Going by memory I believe your stock springs are 95 gram. The kits come with 65 gram, and 115 gram. Just...
  33. Replies
    21
    Views
    776

    Re: 1995 Wave Venture 700 guidance

    You are on the right path, sounds like your machine is overdue for a tune up, and some maintenance.

    Make sure you use genuine Mikuni brand carb kits, and needle and seats. DO NOT use the needle...
  34. Re: ** NO pop-off pressure on my 1993 Waverunner **

    Bad needle and seat.... That or installed incorrectly... (I have seen many times, the needle arm/spring not seated correctly)

    Did you use genuine Mikuni brand needle and seat, and kit when you...
  35. Replies
    16
    Views
    740

    Re: Piston pin size 750

    there are only two piston pin sizes.

    20mm (small pin), or 22mm (Big pin)

    The engine in your picture is a small pin 750. If you ordered small pin pistons, and they do not fit, you got the wrong...
  36. Replies
    6
    Views
    506

    Re: Cleaning Bendix

    New OE here. Do not buy any cheap, gold drives, they fail as well.....

    https://www.watcon.com/electrical/starters/bendix-drive-1
  37. Replies
    6
    Views
    358

    Re: 750sx '92 spark plug gap problem

    Lower rod bearing or other material bouncing around inside.

    The only way to know for sure is a complete tear down and inspect.
  38. Replies
    6
    Views
    506

    Re: Cleaning Bendix

    DO NOT run that.....

    Rust on a bendix is bad. A bendix can, and will come part, ruining your stator, flywheel, possibly your cases, and I have even seen them take out the front seal causing a lean...
  39. Re: Which is best, Small pin or large pin Kawasaki 750 motors?

    Edit;

    After checking part numbers, the 95 IS the same, #22 cyl as the 93-94.

    So to answer your question yes.......
  40. Replies
    7
    Views
    536

    Re: 650sx cooling help

    If you keep blowing gaskets, my guess is you have another issue. Head warped/cracked, top of cyl not straight/true, not torqueing or re-torqueing correctly, etc.

    There should be no need for...
  41. Re: Installing Westcoast Pipe, what adjustments are needed?

    Yes. I have seen it a few times now, and were all on Westcoast pipes.....
  42. Replies
    11
    Views
    1,193

    Re: 1986-1995 X2 driveshaft.

    New X2 shafts in stock here, $299 + ship;

    https://www.watcon.com/jet-pump-drive-line/drive-shaft/x2-drive-shaft
  43. Replies
    2
    Views
    485

    Re: 1995 Waveraider split exhaust hose

    Blockages can occur anywhere in the cooling system.

    Typically if an exhaust hose blows out, it is from heat, and a blockage in the exhaust somewhere.

    Take off all lines, small hoses, etc and...
  44. Re: Installing Westcoast Pipe, what adjustments are needed?

    Be careful sandblasting.... We see many times people do this, and plug up the water cooling jackets.
  45. Replies
    2
    Views
    524

    Re: WaveRunner III Steering issue

    Clip to hold the cable is in the rear mount, under the plastic nut. I am guessing though your cable is broken internally. ....
Results 1 to 45 of 9400
Page 1 of 209 1 2 3 4
Powered by vBadvanced CMPS v4.2.0