Search:

I pmed you about a 750 pole spring...

lol... I have a BFH... but The spring does not line up with the holes on the pole... I put the pole on without the spring... inside the stock handle pole there looks like black flotation...

:salook::Banane35: Glad you figured it out.... I am just seeing this..but Always start the engine before the hose...

was that from a dual carb setup maybe???

Ok... I have an 89 650 SX
k & N F/A
wesrcoast pipe
jet sport 44 mm intake
44 mm Mikuni SBN rebuilt with geniune mikuni rebuild kit & New N&S from Watcon late last season.
was winterized properly...

Any you guys have any ticks of installing the handle pole? My original one had a crack, I found a used one I swapped everything over ran cables....I just cant seem to line up the holes with the...

I have a pole I just cant seem to get it back on ..whats the trick to lining up the pole holes and spring??????

Just use dental floss to install rubber check valve keepers...no need for special tool...

wound up tying a rope to the pump then tied other end of rope to a tree...hooked back up to the trailer and pulled...pump finally pulled free....gotta love working on salt water machines... but I got...

I have one of these in my WR500 that I swapped a vxr 650 into....with a coffmans sizzler and this waterbox..it sounds ****y... lol it goes pretty good to...kids have a blast on it...

How much for that display ?

Hello all...I have seen some posts about getting this jet pump off..But still have questions... I have removed the reverse bucket ? nozzle assembly. I removed the 5 bolts holding the wear ring onto...

My handle pole on my 650 sx is cracking at the pivot where the bushings and bolt go through...so I am looking for a new handle pole... If I am replacing it, my thoughts are I should shorten it if...

I'm still looking need pics

wasn't there somone on here that made aftermarket aluminum poles?

how much?

still have the pole? Think it will fit an 89 650 sx?

I might be interested in the handle pole..I want it for my 650 sx...I think it should fit..

you wouldn't have to "tune the carb" just leave all your settings alone and rebuild the carb....or pay attention on your mixture screws how many turns out they were and write it down to make sure you...

"its now running as slow as ever".....LMAO.....

of course that old 550 didn't have reeds...that's why the screw made it to the crank.... but I still like a shot of premix to the carbs for quick starting...

I have a good cdi for that boat...I know I have a used crank for it..I have a whole engine but it would cost more to ship than the engine is worth..but I can pull parts and sell if you want to keep...

I clean them real good and hit them with a heat gun.. I think it brings the oil in the plastic / rubber back to the surface but it does get shiny again..just try to be consistent with how long and...

so what did it wind up being?

I had a similar issue on Saturday. Friday I un winterized it. My 96 wave raider 1100...uncovered it, put the charged battery in got it fired up on the old plugs to clear out the fogging oil...started...

lol ok that makes more sense...I was going to put iton today and I got the wheel and my new idle screw and was like...wait a minute...then rode something else...lol Thanks man..Let me guess... if I...

Here is a stupid question..... I just purchased a throttle wheel drum for my 650sx 44mm mikuni sbn...I didnt like the way the cable hooked up to the throttle thing on the carb. I already had to flip...

I have two CDK 2 carbs for sale. I bought them for something years ago and couldnt use them....make an offer.. I'm thinking 100 bucks plus shipping for the pair 50 per carb?? PM me for pics

I meant the TS not X2

Didn't X2 cylinders have some kind of bracket? maybe the holes are for that? Maybe Previous owner rebuilt the engine or swapped an engine from an x2? Just throwing it out there to see if it sticks.

I would be interested as a spare for my raider... but that price is too high for it to be sitting on my shelf until IF /Maybe I need it sometime... I respect your price and if I needed it to get back...

how much for 4 good Kawasaki 650 motor mounts? shipped to 08086?

how much? are those domes good for pump gas? I am looking for a head for my 650

couldn't you use it as is but only hook up one set of plugs per cylinder like the old two stroke endure bikes?

looking for a good set of 650 cylinders I am going to bore them anyway...but not too deep of gouges

how much for the jugs if still available? shipped to 08086

still available?

:rock:

I have the base with no seat ..its from a wr500..AND...I'm in NJ...lol so let me know...

On my raider 1100, The carbs are perfect and that thing was always hard to start when cold. It had to do with getting the fuel lines full and getting fuel mix to carbs. I fixed this with a primer....

556812

looking for 9 stainless studs for my F/A.... going on a raider 1100 stock carbs I believe 38mm.... anyone have an idea where to get these? I have probably asked before...

There is a small dock at the ramp for temp. tie up while you park your rig. It is $12 to use ramp and park. There is a beach for swimming and you are not allowed to have boats or PWC at the swimming...

Will be trying again this weekend.

What kind of paint did you use?

I never made it. I had trailer light issues and then saw how windy and chilly it was going to be then just scratched my plans. I am watching weather this week and will get down there...