Search Results - PWCToday
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: SWFL SJ Rider; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Re: 550sx airleak bottom flywheel side intake manifold bolt?

    Bandit I'm going to try that. The hole is pin head size, I do not know where an exit hole is -just that bubbles appeared to be coming out of back side of exhuast bolt hole. I just put some acetone on...
  2. Re: 550sx RAD flywheel re-installation after replacing rear seal?

    Last RAD flywheel I had was in the early 90's didn't remember what came with. Posted answer I found to my question to help anyone else reading this thread. I find it interesting why they wouldn't...
  3. Re: 550sx RAD flywheel re-installation after replacing rear seal?

    Found a copy of the RAD instructions someone uploaded to 550sx facebook group. Torque to 100lbs and use tab washer. Strange it did not have one installed.
  4. Re: 550sx airleak bottom flywheel side intake manifold bolt?

    577255
    577256
    Found like a pin hole inside intake on cylinder. do not see where it comes out-maybe it goes diagonally to inside bolt hole? What is my solution now? Can I epoxy over the hole? What...
  5. Re: 550sx airleak bottom flywheel side intake manifold bolt?

    Bill,
    Thanks for the reply. Ski is 91' 550 reed motor, I should have elaborated- intake manifold hole on the cylinder is open on back-air is coming out the open back end of bolt hole. everywhere...
  6. 550sx airleak bottom flywheel side intake manifold bolt?

    550sx was leaking air rear seal and flywheel side intake manifold bolt. Rebuilt with new seals. Now it is only leaking bottom flywheel side bolt on intake manifold. I used 1211 all gaskets both...
  7. 550sx RAD flywheel re-installation after replacing rear seal?

    rear crank seal is leaking so I have to remove flywheel and coupler, split cases to replace, I have a RAD flywheel. Does anyone have instructions on the re-installation, is it same as stock-torque...
  8. Re: 550sx exhaust bolt thread & tap size question

    thanks, I was able to step drill the remaining bolt and tap threads.
  9. 550sx exhaust bolt thread & tap size question

    I broke off top left exhaust manifold to cylinder bolt on 550sx I'm rebuilding. could not remove other than drilling out most the bolt out, dont think i hit any threads in the bolt hole. I wanted to...
  10. Re: Genuine keihin and winderosa carb rebuild kits

    I realize this is an old post. Do you still have any of the geniune Keihin kits left?
  11. Replies
    9
    Views
    551

    Re: WTB 550 engine bed plate

    Thank you but I found one locally.
  12. Re: NOS 550sx reed cylinder - new in box

    I understand the arguement comment. Can you pm explanation. Just curious looking for information. I have 550 reed with a c stamped above exhaust manifold.
  13. Replies
    1
    Views
    2,002

    Re: Blowsion tubbies II (brand new!)

    do you still have the tubbie II for sale?
  14. Replies
    9
    Views
    551

    Re: WTB 550 engine bed plate

    okay let me know price and send pic of condition when your able. thanks
  15. Replies
    9
    Views
    551

    Re: WTB 550 engine bed plate

    Just need one in good shape. Can you send pic, How much shipped?
    Thanks
  16. Re: NOS 550sx reed cylinder - new in box

    What do the different stamps mean?
  17. Replies
    9
    Views
    551

    WTB 550 engine bed plate

    Looking for 550 engine bedplate in decent shape. Anyone have one to sell?
  18. How to remove 550sx skat trak impeller

    Rebuilding an old race ski 91 550sx, was told impeller was bound up in pump liner. I see damage in liner and will replace. I have the pump out and seperated into its sections turning by hand seems...
  19. Replies
    1
    Views
    506

    38bn on 550 pp help -lower pop off?

    Almost have my 550 restortation for the kids up and running. 550 pp, bread box exhaust but 38bn carb, 110 compression, leak down test not losing pressure, rebuilt carb, replaced needle and seat 1.5,...
  20. Replies
    11
    Views
    1,309

    Re: Help 550 not starting

    Not sure on year of tip or bottom end, its a complete motor i bought. Cylinder has 530A stamped on it. the 38BN has a bolt in return fitting that is hollow and has perpendicular hole below the head-...
  21. Replies
    11
    Views
    1,309

    Re: Help 550 not starting

    Update- performed leak down test. Engine hold 10psi for 15 plus minutes. Took exhaust elbow off to pace leak down testing plug the exhaust have dark grey oily sludge in it the exhaust a lot of it....
  22. Replies
    11
    Views
    1,309

    Help 550 not starting

    I have 550 pp breadbox exhaust, compression 110 each hole, good spark, just rebuilt 38 bn pop off 15-18 forgot exactly, rev limiter removed. Engine turns over great but wont ignite fuel. thought...
  23. 550 head installation direction-mines backwards

    I have 89 550 pp motor and 91 reed motor both have the heads install backwards with the only cooling line on side near electrical box. I believe stock have the fitting on the gas tank side of motor....
  24. looking for fresh water ride location south of orlando

    Looking for a freshwater spot to ride south of orlando- like near lake placid, sebring, southwest florida. Any ideas?
  25. Replies
    3
    Views
    315

    Re: WTB 550js cylinder

    Thanks Chuck, I sent you a pm. I can come anytime your available. Thanks
  26. Replies
    3
    Views
    315

    WTB 550js cylinder

    Looking to buy cylinder to for 89' js550 in decent shape, standard bore or close to it?
  27. Machine Shop recommendations in SW Florida

    I'm located in SWFL. Can an anyone recommend a machine shop, I don't mind shipping. Need to bore 89' 550.
    Thanks in advance
  28. Replies
    7
    Views
    1,010

    Who does Cylinder Boring in Florida?

    i'm in southwest florida and need a machine shop to bore 89' 550 cylinder. Any recomendations?
  29. how to clean paint from mating surfaces?

    Bought 550 pp cylinder and breadbox pipe pipe, previous owner painted all gasket mating surfaces, intake and exhaust tracks. having difficult time removing the paint with razor, heat, wire brush. Any...
  30. Replies
    1
    Views
    722

    Help splitting 550pp cases

    Does anyone have tips for splitting 550 pp cases? cylinder is off, all fasterners off, used razor blade to cut thought sealant between cases and still can't get them to sperate. Any help would be...
  31. With r & d pro lock adapter 44mm 206-01144

    Need three will buy one to three.
  32. WTB r & d pro-life adapters 44mms need three

    Need three pro-life r & d performance 44mm adapters, part number 206-01144.
  33. Re: Riva reed spacer yamaha 1200, r&d reed stuffers yamaha 1200

    Still have spacer?
  34. Scarb rebuild question SBN 44- what is this tiny hex screw

    I am rebuilding SBN 44's for gp 1200, I noticed a very small hex screw recessed into carb near bottom of carb same side as needle and seat goes, not the high or low speed jets 478134but a smaller...
  35. Re: HELP-gp1200 crankcase question. What are these holes and this rubber piece

    Thanks for the reply. These are not the pulse lines-i am familiar with those. There are 2 holes I am trying to describe. One between each of the intake tracts. This is completely stock ski. Carbs...
  36. HELP-gp1200 crankcase question. What are these holes and this rubber piece

    took the carbs off 1997 gp1200 and noticed two small holes in crank case between the intake tracts. on477860477861477862477863e looks to be covered with torn paper or cotton. the other had this...
  37. single carb setup for 62T- freestyle

    Single carb set up. 44 mikuni, stock sj airfilter, single intake mani, 62t reed spacer, reed cages, reeds, whole setup ready to go. please reasonable offers, I am in no rush to sell. I would consider...
  38. What aftermerket F/A are u running on gp1200 65u?

    Want to upgrade my stock gp 1200 a little. already have impeller and grate. What F/A are people running? I was think of using some old jetsport ones form the 550 days.
  39. Replies
    0
    Views
    605

    WTB after market F/A gp 1200 65u

    looking for aftermarket F/A for 1997 gp1200, must be reasonable priced or open to trade of 550 or RN parts.
  40. Re: WTB jetsport 44 mm falme arrestor-need two

    PM sent
  41. Re: resurrecting 1997 gp 1200, grease questions and general prep

    Thank You.
  42. resurrecting 1997 gp 1200, grease questions and general prep

    I have an GP1200 been sitting for 8 years, turns over. I am rebuilding the carbs. before I begin to use I want to do as much maintenance as possible. What type of grease do I use in the grease...
  43. WTB jetsport 44 mm falme arrestor-need two

    If you have any of these old flame arrestors I am looking for two. will buy singles.
  44. Replies
    0
    Views
    577

    gp1200 65u carb rebuild question,,

    I have read many post on the subject. if going prefix Most threads mention 135 main, 100 pilot, 1.5 need and seat with gold spring, drilling carb and restricting return line. but they usually refer...
  45. Replies
    9
    Views
    1,894

    Re: Strange rebuild question

    Yeah, I remeber that. I'll look for you at New Pass. Thanks.
Results 1 to 45 of 51
Page 1 of 2 1 2
Powered by vBadvanced CMPS v4.2.0