Search Results - PWCToday
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: restosud; Keyword(s):

Page 1 of 44 1 2 3 4

Search: Search took 0.14 seconds; generated 32 minute(s) ago.

  1. Re: WTB SXR 800 Head, Pipe, Intake Grate, Flywheel

    have new ada girdle head.
  2. Thread: Sxr mod

    by restosud
    Replies
    3
    Views
    161

    Re: Sxr mod

    air temp sensor mounted right above the E box.looks like a short piece of brass and has a green 2 pin connector.remove sensor and jump the 2 wires.
  3. Re: wtb sxipro battery tray and back right bumper

    have the battery tray.$48 shipped plus paypal.
    don't waste your time with the factory rear sponsons.
  4. Replies
    3
    Views
    134

    Re: Js550 crank missing orings/washer

    all you can replace are the outer bearings.unless you have knowledge and tooling to split the crank
    definitely replace the front bearing as it usually takes a beating
  5. Replies
    3
    Views
    134

    Re: Js550 crank missing orings/washer

    large washer is a must have.
    if bearing oring,then bearing house should have them but starting in 86 the bearings had an orange plastic insert.85 and older had groove in bearing outer race for oring.
  6. Replies
    2
    Views
    189

    Re: Good Kawasaki 1100 Motor needed

    have a couple zxi's here. $800 plus ship from 70118.look up shipping costs.
  7. Replies
    12
    Views
    335

    Re: Fuel issues (750 sxi pro)

    check your fuel flow wot.pumps,restrictions in fuel line,pet**** etc...restrictor size,any fuel going back to tank at wot since you are certain your prop is not the issue.
    for info,back in the...
  8. Replies
    12
    Views
    335

    Re: Fuel issues (750 sxi pro)

    ok.as long as you're satisfied with this info...
    so,what rpm are you seeing exactly??
  9. Replies
    12
    Views
    335

    Re: Fuel issues (750 sxi pro)

    could be getting hot or detonating since overloaded.
    what rpm are you reaching when it works well?
  10. Replies
    12
    Views
    335

    Re: Fuel issues (750 sxi pro)

    unless you've bored the crap out of the pump nozzle,that 15/20 is way too much!
  11. Re: Impros Impeller Installation -- Is this a flow cone flange?

    no,in the back where the pump shaft pokes out.the little pointy cover ( flow cone)is held on with 2 bolts
  12. Re: Impros Impeller Installation -- Is this a flow cone flange?

    are you sure these instructions apply to your pump?
  13. Replies
    10
    Views
    409

    Re: js440 bilge not working

    elbow piece vacuum hole is clear?
    you could have a water leak filling up hull too.
  14. Replies
    6
    Views
    384

    Re: Likely to explode?

    don't think this is what op had in mind!!
  15. Replies
    6,871
    Views
    575,107

    Re: Can't get enough of all craigslist jokers!

    and there's probably a reason for that!
  16. Re: wtb kaw 750 sxi pro buklhead exhaust hose

    $35 for a new one https://www.kawasakipartshouse.com/oemparts/a/kaw/500b251af8700223e478e55e/muffler-s
  17. Replies
    4
    Views
    232

    Re: Sxr complete engine

    $1720 plus ship.
    have a set of 48 novi's for this world finals class motor.
    you would also need a pipe to get the hp out of it.
  18. Replies
    4
    Views
    232

    Re: Sxr complete engine

    have a bill chapin of R&D ported 800.used as a back up for world finals.only broken in .short block with bedplate and R&D girdle head.
  19. Replies
    27
    Views
    552

    Re: Grinding noise? Help ASAP!!

    shaft should slide into bulkhead bearing with no discernible play.not a press fit ,only hand pressure should be sufficient to push it through.

    and stop posting in this "parts for sale" section!
  20. Replies
    27
    Views
    552

    Re: Grinding noise? Help ASAP!!

    this thing is like new!
  21. Replies
    6
    Views
    702

    Re: SXR 800 - drop in ready

    if you separate interested in intake manifold
  22. Replies
    5
    Views
    429

    Re: Leak Down a Test Question

    some air will leak out through the pipe water sprayer into cooling jacket but you can just plug the outlet of pipe and pump the whole thing up.
    get an expandable rubber plug from plumbing section at...
  23. Replies
    5
    Views
    292

    Re: Throttle shaft leaking

    dremel the threaded portion or just back them out with a good phillips screwdriver.pull out butterfly and push shaft out.
    new shaft and new screws.loctite and pinch the new screws with vise grips...
  24. Replies
    6
    Views
    434

    Re: 550sx pump info

    no. the OP nozzles only allow for larger bore if needed.
  25. Replies
    9
    Views
    571

    Re: 650sx Westcoast dual red carbs!

    standard bn 38 bolt pattern.
  26. Re: 550sx quick steer plate and zero degree bars

    have straight bars.
  27. Replies
    7
    Views
    337

    Re: Skat Trak Swirl 10/18 thin blade SXR 800

    yes and yes
  28. Replies
    19
    Views
    679

    Re: Crankshaft seals on 1100 zxi

    standard thread on coupler and flywheel needs a puller.
  29. Re: New Kawasaki 550 Coffman pipe and water box.

    i thought your tinder pics had a no purchase required clause.
  30. Replies
    4
    Views
    411

    Re: Ultra 150 crankshaft

    crankworks, competitive crankshaft are a couple.
  31. Thread: Superjet pump

    by restosud
    Replies
    2
    Views
    173

    Re: Superjet pump

    got vane section.clean no corrosion.$50 plus ship and paypal.
  32. Replies
    10
    Views
    394

    Re: 1996 zxi 1100 leak at shaft seal

    should not have water coming through the bolts at all as they are blind holes
    check your hull for cracks etc...
    if moving then water being scooped keeps the tunnel pressurized.try with engine...
  33. Replies
    4
    Views
    204

    Re: WTB Novi 46 A booster

    got 48's A
  34. Replies
    10
    Views
    463

    Re: 750 sxi water injection

    are you running the ffp dry pipe made for sxi pro?
  35. Replies
    8
    Views
    343

    Re: flywheel cover spring/washer combo

    google kawasaki parts . there are plenty of vendors out there with parts fiche online.
  36. Thread: Sbn 48??

    by restosud
    Replies
    7
    Views
    359

    Re: Sbn 48??

    is there "brm" engraved on it?
    could be a full spectrum 48 also
  37. Replies
    8
    Views
    1,907

    Re: Sxr 1500 must have modifications

    damn old guy.this was from last year!
  38. Replies
    7
    Views
    553

    Re: 650sx vin and titles needed

    yes but you have registration papers just like in louisiana.
  39. Replies
    7
    Views
    553

    Re: 650sx vin and titles needed

    oh boy. here we go again!
  40. Re: 46mm or larger triple carb and intake setup for kawi 1100.

    have new novi 48 and split r&d manifold
  41. Replies
    9
    Views
    468

    Re: How does it work?

    those are different.
    and which wire are you measuring???
    exciter coil provides both power and trigger signal to cdi.cdi then fires the coil.
    what you're reading is the input a/c voltage on...
  42. Replies
    7
    Views
    319

    Re: Kawasaki Small Pin top end Rebuild

    fullbore does great work and is not too far from you.go that route.
  43. Replies
    5
    Views
    444

    Re: 550 Ocean Pro/aluminum bed plates

    oem cast ones were the best.light and rigid.
    the OP and skihaven can allow for too much flex and vibration and wear the couplers.
  44. Replies
    9
    Views
    468

    Re: How does it work?

    what model ski?
    if just independent coil like 750sx then the coil always has + power applied to it and cdi breaks ground to trigger spark.
    sounds normal to me.
  45. Replies
    3
    Views
    5,195

    Re: West end standup riding

    yeap.
Results 1 to 45 of 1940
Page 1 of 44 1 2 3 4
Powered by vBadvanced CMPS v4.2.0