Search Results - PWCToday
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: john zigler; Keyword(s):

Page 1 of 211 1 2 3 4

Search: Search took 0.51 seconds.

  1. Re: 95 Waveraider 700 cranks but will not start

    You may just be flooded. Maybe you have a carb issue causing too much fuel.

    Change the spark plugs, turn the fuel off, hold the throttle wide open, and try again.

    Also, I will say one more time...
  2. Re: New to me 1994 X2 with mods I don't understand Electronics strapped to the tank

    Looks like someone changed your engine / electronics with one from a TS (Also a 650)

    If your choke is missing, yes, I would add a primer.

    Nothing wrong with the Keihin carb. If you want to...
  3. Replies
    2
    Views
    123

    Re: 440/550 exhaust block off

    I show I have this PJS one still.... $20 + ship.

    https://app.photobucket.com/u/radracingpics/a/d5443324-b8fb-4899-ae21-6f83f6f3bed7/p/fe7a48b9-8e3a-4c86-bfec-a6fc09373fbe?mode=zoom

    You can...
  4. Re: 95 Waveraider 700 cranks but will not start

    For an engine to run, you need spark, fuel, and compression. We need to determine what is missing from this equation, and trouble shoot from there. NEVER assume anything.....

    Check compression.
    ...
  5. Re: 750sx impeller upgrade with stock motor

    9/15 is Skat numbers. You cannot compare brands by number. Blade design, blade over lap, hub design ect all make a difference in how an impeller loads the pump. Not to mention the two do not measure...
  6. Replies
    8
    Views
    260

    Re: ISO 44mm sbn carburetor

    Thanks for the kinds words.

    I might have a good used carb, (In need of a rebuild).

    Send me an email and remind me to look, or give me a call at the shop.

    John
    watcon@watcon.com
  7. Replies
    8
    Views
    260

    Re: ISO 44mm sbn carburetor

    Just a FYI;

    New they retail for $240 from Mikuni.

    I sell them on my web site for $220 + ship.

    Depending on your application, you will need to re- jet it. We sell a jetting kit for $40. This...
  8. Replies
    3
    Views
    297

    Re: Replacement starter relay

    I have two OE Yamaha types in stock here. Early & Late 2-stroke;

    https://www.watcon.com/electrical/start-relay
  9. Re: F.S. EME ROID Carbon Freestyle ski $12,000

    Still available.
  10. Re: WTB SXR prop, x2 driveshaft, 750 intake grate

    X2 driveshafts are getting difficult to find used, and can be very expensive. (Used)

    We have new, $299 + ship

    https://www.watcon.com/jet-pump-drive-line/drive-shaft/x2-drive-shaft

    The Solas...
  11. Re: Needing some help - my engine (jet ski's engine acttualy) was flooded.

    With the Oil filter removed, and by cranking the engine over while holding the throttle wide open, you can suck more oil out of the oil filter canister. Keep cranking/sucking until no more oil comes.
  12. Re: Needing some help - my engine (jet ski's engine acttualy) was flooded.

    I have had to do up to 6 oil changes to get all the water out.......
  13. Replies
    16
    Views
    702

    Re: 750 cdi with timing advance

    You are correct, and this is why it is important to tune properly to match your mods done. You cannot just make changes without tuning. Sounds like you were lean, and also did not run the correct...
  14. Replies
    16
    Views
    702

    Re: 750 cdi with timing advance

    Your problem had nothing to do with timing......
  15. Replies
    2
    Views
    249

    Re: 62t 701 cylinder

    $500 + ship.

    Freshwater 62t cyl, with NEW pistons, rings, pins, clips, top end bearings, and top end gasket kit. Cly will have fresh bore.

    John
    watcon@watcon.com
  16. Replies
    11
    Views
    713

    Re: Take a look! 650sx exh.

    2 in = 2 out.

    Plug the middle original single in.
  17. Re: Nedra Atwood, AKA The Cowbell Lady-RIP

    So sad, RIP Nedra.... You were loved, and will be missed.
  18. Replies
    16
    Views
    702

    Re: 750 cdi with timing advance

    Yes, you are fine with this combo. Unless you have high compression (more than 175) it is not a problem with premium pump gas.
  19. Replies
    5
    Views
    509

    Re: Stock SXR exhaust

    I have a complete pipe here, freshwater.

    $100 + ship

    John
    watcon@watcon.com
  20. Replies
    12
    Views
    688

    Re: scored this js550

    I do 8 psi. You do not need more than that. Too much, and you will just blow out the seals.
  21. Re: New to me 03 SJ. Pulled motor, what to do while im in there?

    I seal up around all tubes, (Cooling and steering), and the exhaust also as none are sealed from the factory to the bulkhead. water can and will get in here.

    Again, I use JB weld stick putty to...
  22. Re: 550sx reed case and too big 77mm pistons?

    Don't forget - You Need to clearance the base gasket as well to match.
  23. Replies
    12
    Views
    688

    Re: scored this js550

    DO a leak down test on the engine. I am sure your crank seals are leaking wand will need to be replaced. (Will give you a lean condition)
  24. Re: New to me 03 SJ. Pulled motor, what to do while im in there?

    While the engine is out, seal up the hull....

    There is 2 large holes in the bulk head, originally covered with a sticker. Tray foam is exposed here, and can soak water. I use JB weld (Stick) putty...
  25. Re: WTB kawi750/800 single 44/46 Intake manifold

    New here if you cannot find used;

    https://www.watcon.com/fuel-system/intake-manifolds/kaw-750-intake-manifold
  26. Replies
    17
    Views
    1,802

    Re: Cylinder Boring

    Please call me at my shop, I will get all your info, start a work order etc. ph number is in my signature here, all contact and ship to is at my website watcon.com
  27. Replies
    17
    Views
    1,802

    Re: Cylinder Boring

    Yes, we chamfer the ports. I leave ring end gap to the engine assembler.
  28. Replies
    17
    Views
    1,802

    Re: Cylinder Boring

    I asked my guy, and as long as the bore is larger than 2", yes we can do it.
  29. Replies
    17
    Views
    1,802

    Re: Cylinder Boring

    Maybe. Call me at the shop during hours.
  30. Re: F.S. EME ROID Carbon Freestyle ski $12,000

    Bump for good deal....
  31. Replies
    3
    Views
    445

    Re: 650sx crank/case question

    Any noise, you need to rebuild crank.
  32. Replies
    17
    Views
    1,802

    Re: Cylinder Boring

    We do machine work here, southern WI. I have pistons kits, gaskets, and cn bore your cyl to match.

    John
    watcon@watcon.com
  33. Fish's Excellent Jet Ski Race tour video adventure

    Now in stock and for sale here, Re-release of Fish's Excellent Adventure. DVD of the lifestyle 1991 race tour.

    Lots of vintage, girls, racing, freestyle, rapids, etc. $15 + ship

    ...
  34. Replies
    3
    Views
    349

    Re: Kawasaki 750/650 pump wedge

    Pretty sure I have one (or two)

    Send me an email watcon@watcon.com and remind me to look when I am in the shop tomorrow, or call my shop tomorrow during hours.

    John
  35. Re: Few questions about fuel/oil line size and other questions

    Polaris had a temp sensor, in the cooling rail on top of the heads. Should be a brass fitting with tan wire.
  36. Re: Few questions about fuel/oil line size and other questions

    Fuel lines are 1/4". Oil injection lines are 1/8"

    We have genuine Mikuni carb kits, and triple outlet fuel pump kits in stock here for your Polaris.

    I understand NOT wanting to spend a lot of...
  37. Replies
    2
    Views
    250

    Re: 550 bored nozzle

    I have nozzles here, and can bore one up for you. $90 + ship. (Nozzle assy with steer nozle)

    John
    watcon@watcon.com
  38. Replies
    3
    Views
    713

    Re: Hello Everyone

    Hi James, welcome.
  39. Re: F.S. New Old Stock Ocean Pro Chubby Mat Kaw 440/550 $75

    We use DAP Brand, weldwood contact cement. Red Can (Not the green can), available at home depot, menards, etc.
  40. Replies
    7
    Views
    827

    Re: 1999 SXi Pro full tear down

    No one here can tell you if you need a bore or not for sure.

    You need to measure your cyls, check for out of round, and taper. Then you need to know your piston to cyl wall clearance. If you are...
  41. Replies
    6
    Views
    1,296

    Re: Newmiller, mcn6 still around?

    I speak with him often, he just ordered some pistons from me a few days ago. I am sure he / everything is fine.... I think he is just busy.
  42. Replies
    6
    Views
    294

    Re: WTB zxi 900 stock ride plate

    Pretty sure I have one....

    $25 + ship if I do.

    Send me an email watcon@watcon.com and remind me to look. (Or call my shop)

    Sorry though, no pay pal. I take Visa, and Master Card only.
    ...
  43. Replies
    3
    Views
    632

    Re: Sanding the hull ribs down?

    They are there for hull strength and rigidness (< is that even a word? lol) I would not remove them.

    John
  44. Re: Mystery engine mount identification - Superjet

    It looks like someone has swapped in engine mounts from a sit down Wave Runner.

    These are larger and stronger mounts. We too have used them in Super Jets, BUT in most cases they cause the engine...
  45. Re: F.S. EME ROID Carbon Freestyle ski $12,000

    Monday morning Bump
Results 1 to 45 of 9476
Page 1 of 211 1 2 3 4
Powered by vBadvanced CMPS v4.2.0