Search Results - PWCToday
pxctoday

» Log in

User Name:

Password:

Not a member yet?
Register Now!

» Find OEM Parts

» Jobs

» wallpapers

Search:

Type: Posts; User: kard150; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    1,271

    Re: 03' STX 1200r Water Leak **Please Help**

    I had the same thing on a 02 stxr. I comes from wave jumping and the plate gets pushed up off the hull. You can try resealing it but if the plate is pushed up then you'll have to remove the motor...
  2. Replies
    4
    Views
    1,263

    Re: 2006 kawasaki stx 1200 impeller

    Until you start to mod the motor I would stick with the Oem impeller. You can send it to Sbt and they'll reweld it for $25 Ken
  3. Replies
    11
    Views
    1,445

    Re: buying 2000 ultra150 questions

    Only the first demo models had compression listed as 150 psi. Most are around 120 psi give or take 5 psi. You know having stock heads does not mean their not recut to raise compression. Ken
  4. Replies
    4
    Views
    1,263

    Re: 2006 kawasaki stx 1200 impeller

    You'll need an Impeller tool and a large vice.

    Pull the pump and remove the tail cone.
    Insert the flat part of the shaft in the vice and then insert the tool into the impeller, It will come...
  5. Replies
    11
    Views
    1,547

    Re: Hull Paint/Color Code for a 97 WaveVenture??

    http://www.colorrite.com/

    Check this site out it has the factory paint available in what ever size paint you need. Ken
  6. Replies
    11
    Views
    1,934

    Re: 2002 ultra 150 help?

    Was their smoke inside the hull when you pulled the seat? Ken
  7. Replies
    3
    Views
    5,829

    Re: stroker crank for stxr

    From what i've read its not a Stxr but a boat that Zapata is marketing and racing using a Kawasaki based hull and a homemade looking top deck with a "2000cc four cylinder 2-stroke" motor which looks...
  8. Replies
    3
    Views
    872

    Re: whats the biggest bore possible

    Check out Group k. Ken

    http://groupk.com/k1100bb.htm
  9. Replies
    64
    Views
    10,795

    Re: Ultra 150 Engine Failure Analysis

    I'm confused. My motor was never mentioned here.

    If you have a triple piped boat what carbs are on it? Ken
  10. Thread: Kawi ultra 150

    by kard150
    Replies
    10
    Views
    1,269

    Re: Kawi ultra 150

    All the stock heads are the angled plug heads.
  11. Thread: Kawi ultra 150

    by kard150
    Replies
    10
    Views
    1,269

    Re: Kawi ultra 150

    Its hard to tell from the pictures but its clear the carbs were running rich from the piston wash so detonation doesn't seem likely unless it ran out of fuel somehow. Can you post a close-up of...
  12. Replies
    64
    Views
    10,795

    Re: Ultra 150 Engine Failure Analysis

    I'm an A$$?? You rebutt everyone on this post and you start the personal stuff and I'm the @ss. Your a frikin "Seadoo Mechanic" and you act like one. I'm sorry i didn't mean to offend Seadoo...
  13. Replies
    64
    Views
    10,795

    Re: Ultra 150 Engine Failure Analysis

    I'm just glad that to hear I know nothing about Ultra 150's and Stxr's and someone like Waterhawk is hear to straighten me out. Sounds like he treats them all the same....Its a "Seadoo" so fix it...
  14. Replies
    64
    Views
    10,795

    Re: Ultra 150 Engine Failure Analysis

    Premix only isn't the best answer for the Kawi1200. If your worried just add alittle oil to your gas and you'll be fine. Ken
  15. Replies
    5
    Views
    1,639

    Re: ultra 150 - oil out of exhaust

    Does it feel like its low on power? I've seen a bad fuel pump cause alot of oil to shoot out the exhaust because the pump won't pump enough fuel to a cylinder but the oil pump runs just like before...
  16. Replies
    64
    Views
    10,795

    Re: Ultra 150 Engine Failure Analysis

    Its hard to tell from the pictures but it looks like #2 was lean as well as having alot of blowby. It maybe looks that way from when it grenaded.

    If you want the machine to run like its...
  17. Replies
    37
    Views
    5,700

    Re: 1200 stx-r help!!

    I have no idea what that is on your piston or where it could come from. But your pistons looks lean from the piston wash and I have to believe that the material came from the cylinders somewhere. ...
  18. Replies
    15
    Views
    2,583

    Re: ultra 150 2000 maybe carb issue? posted video

    Have you tried running it without the seat or with the seat slide back. This is a test for an Exhaust leak. If your hose is leaking or your waterbox leaking the hull will fill up with exhasut and...
  19. Replies
    15
    Views
    2,583

    Re: ultra 150 2000 maybe carb issue? posted video

    First thought is a bad plug and the other is bad pump bearings allowing the impeller to make contact with the wear ring. And finally you might need to pull the airbox and check to see if the holes...
  20. Re: 99 Ultra 150; changes its mind on how it wants to run

    Sounds like your oil pump cable is off the pulley and wide open. You might want to check that. Even so it should run faster that 10 mph unless you fouled more than one plug.

    It will run fine...
  21. Replies
    7
    Views
    2,081

    Re: 1200 stx-r vibation problem

    You say it still revs to 7000, is that in the water or out? If thats in the water then I would say your counterbalancer is not lined up correctly if that is out of the water maybe your plug wires...
  22. Replies
    11
    Views
    3,660

    Re: Ultra 150 problem

    The Ultra doesn't use alot of oil to begin with and thats why you might think something is wrong. I've been playing with Ultra's for the last 8 yrs and I've never heard of an oil pump failure. It...
  23. Replies
    11
    Views
    3,660

    Re: Ultra 150 problem

    Ultras are known for fouling plugs so the first thing to do is replace them and see if that cures it. Any motor will run fine out of the water because they have no resistance out of the water so...
  24. Replies
    11
    Views
    2,668

    Re: STX-R flame arrester

    What you have is someones version of a common airbox mod for the Kawasaki 1200's. usually its just one hole directly over the carb throat.

    The screens are the first thing I remove for any kind...
  25. Replies
    11
    Views
    1,818

    Re: Ultra 150: unresolved compression issues

    What size heads are you running for 165psi? Ken
  26. Replies
    11
    Views
    1,818

    Re: Ultra 150: unresolved compression issues

    So all three cylinders read 80 psi? What did the pistons look like when you replaced the rings? any scuffing or pitting? Ken
  27. Replies
    16
    Views
    2,538

    Re: stxr cutting out??

    Just listing a few simple thoughts first. Have you checked to make sure your chokes are not on? Have you checked fuel selector? You could be having a rev limiter for Low fuel, low oil. overheat. ...
  28. Replies
    4
    Views
    822

    Re: Ultra 150 help please

    I would expect its just something thats been laying under the motor but just to make sure you should check for 3 oil ines that go to each carburator. Most look blue with oil in them.

    The lines...
  29. Replies
    12
    Views
    3,991

    Re: Alright.. here goes.. (ultra 150 engine)

    Hey Brandon glad to see your riding again. Your gonna need new cases (both) so order from Kawasaki and then if the rod is bent you'll need a crank. It won't be cheap but don't go the SBT route and...
  30. Thread: 15F vs FX-HO

    by kard150
    Replies
    5
    Views
    1,058

    Re: 15F vs FX-HO

    I think he's asking about the 15F.Ken
  31. Replies
    5
    Views
    1,429

    Re: Ultra 150 Solas Prop Problem........

    If its hitting the Wear ring, you need to ADD shims not remove them. The shims are their to provide clearance and if you remove one your reducing clearance.

    If you already have more than three...
  32. Re: Ultra 150 Pump Question... Like everyone else, I'm in a hurry

    The Ultra pump does not need oil. Just make sure the bearings are good and that you have the nylon thrust washer on the end of the shaft and assemble it.
    Make sure to torque the impeller down to...
  33. Replies
    3
    Views
    936

    Re: Changing the tank on a 2002 STXR

    I don't know about styroform but I ordered my tank from Kawasaki and installed it while the motor was out. The hardest part is getting the old tank out. It's sitting in a molded pocket and you have...
  34. Replies
    4
    Views
    1,276

    Re: Shredmaster ride plate missing holes?

    The holes are not needed so Shredmaster deleted them. Its a common mod to the older plates to plug them. Ken
  35. Replies
    5
    Views
    1,507

    Re: ultra 150 not getting up to full speed

    Theirs no need to take the pump apart you just want to verify nothing inside it and that it's not rubbing the wear ring. Ken
  36. Replies
    5
    Views
    1,507

    Re: ultra 150 not getting up to full speed

    have you done a compression check? I would also pull the pump and inspect just to be sure. Ken
  37. Replies
    4
    Views
    3,523

    Re: 2001 Ultra 150 Leaking at drive shaft holder

    The Bearing carrier is sealed but more than likely its the carrier itself thats leaking. You can order and replace the bearing but you will need to pull the motor. the other place that leaks is the...
  38. Replies
    6
    Views
    1,466

    Re: 15F w/ MAJOR leak !!!! Help please!!

    Theirs a fitting that the driveshaft runs thru that is sealed into place and this is what has come unglued. It happened to my Ultra and it's happened to my Stxr. it's not that hard to fix but you...
  39. Replies
    4
    Views
    1,385

    Re: Truck bed liner on the hull question.

    how about checking out Overtons and looking at the Keelguard. it's a strip that runs down the keel of the Pwc. Thats what its made for.
  40. Replies
    4
    Views
    857

    Re: kawi green paint

    Check out Color-rite. they carry all the manufacturers paint. http://www.colorrite.com/CRPLmanYear.php?typeID=2
  41. Replies
    4
    Views
    1,339

    Re: HElp with a 99 ultra 150

    Typically if your stinger hose melts I wouls say your stinger has something clogging up the water passage going intothe hose but I've never seen a split hose.

    Your speedo has no effect on any...
  42. Replies
    3
    Views
    1,120

    Re: whats a stock ultra 150 cyl. compression

    Around 110-120 psi. is normal. Make sure to hold throttle open while testing, also make sure to charge the battery before testing.
  43. Thread: engine swap

    by kard150
    Replies
    1
    Views
    1,098

    Re: engine swap

    The two motors are nothing alike. The 130 motor is the same as the STX 1100 di and is straight up and down while the 1200 is slanted . You should be able if you move the motor mounts but you would...
  44. Replies
    1
    Views
    713

    Re: 2000 1100 Stz Cooling Sys Blockage

    My Uncle had one and it was doing the same thing by overheating. it turned out the cylinder cooling passages were full of sand. we didn't know this until we tore it down so I can't say if flushing...
  45. Replies
    41
    Views
    4,879

    Re: Ultra 150 Yr 2000 Good Ski ?

    I can safely say that if you have the later model 99 you DO NOT have to use the expensive plugs. If you change heads and go aftermarket with the straight plug holes you do not have to run the 9C...
Results 1 to 45 of 52
Page 1 of 2 1 2
Powered by vBadvanced CMPS v4.2.0