Search:

eBay has a set of new rear sponsons that may work for you.I think there up for $160

Still looking for a shortened lightweight pole

Building a surf ski and looking for an aluminum or carbon lightweight and shortened if possible.let me know if you have.cash or willing to trade.I have a lot of 650 aftermarket parts

Anyone who is legitimately selling on this site will usually text or pick up the phone.Scammers communicate through email mainly.If that is the case just take a pass or get multiple pics from...

I started a thread a while back about these low life’s scamming people.The administator can ban them but cannot let new scammers on.Once again do your research on who you buy from.When I was building...

So I picked up a few ebox’s in good shape from 750ss to get the higher revving cdi out of them mainly but before I fry anything or waste time will it work with a 750sx stator.Cdi model# is 3537.I was...

Looking for a keihin single 42mm carburetor.

It could be endless how much goes into a custom build or conversion.Im at a crossroads myself.I have all kawi parts and hulls.I can’t decide what hull to use on a surf build.650sx or 750sx.The 750...

I would probably get your motor first and see what your dealing with.If you end up with the 750 motor the rhass plate has 2 sets of holes for engine placement on the conversion plate.Its lighter as...

The conversion plate mounts to the motor first then the bed plate is how I did mine.So yes you need the bed plate.
As far as the coupler you’ll need a 550 coupler.Depending on which 650 motor is...

Great build thread came out mint.I like seeing the vision come to fruition.Just something else to consider when looking for motor is your pump and impeller going to produce for you.All the power has...

I can agree 750 over 650 stock straight up conversion for power but on a budget 650 easier and less modification for more than enough power
Yes the ebox and ignition is upgrade but you will need a...

Whatever one comes up first in good shape but I like the stand up model.I ‘m not sure if there is that much of a difference on the 650 engines.750 have big pin and small pin.In that case I like the...

You can run stock 550 water box .I would use aftermarket or gut the 550 box to limit restriction and the baffles and reinstall it.the 650 box probably won’t fit with a stock gas tank.it gets tight...

Go with 650 it’s lighter and arguably can make same low end power as 750 if set up right.plus it’s lighter in the front by pounds just due to the flywheel alone.that can throw off balance off the...

there’s 650 motors on eBay fully rebuilt but you take a chance that it’s done right.you can contact sbt and see if they have motors or are accepting cores for machining.They offer up to 2year...

You may also want to look into if the 62t engine coupler is going to mesh up with the kawi drive shaft coupler.
I sent my coupler out to watcon and they retapped the thread to 20mm.Just something...

I’ve done two 650 kawi motors in the 550.Both cost more than projected just for incidentals in the conversion.rhass make a nice conversion plate and watcon is quality and super fast delivery.dont cut...

Looking for a shortened Aftermarket handle pole -2 for a surf build ski.Im rockering the front and would glass in a new bracket if you have something that may work.new poles are over the top...

What brand manifold is that.Looks dual cooled but not from WC. Mariner or PJS.Kirker used that fin design as well.I bought a freshly powder coated full pipe for $350 shipped a few months ago from...

I wasted more time trying to make older and higher hours motors operate right than it takes to break it down change seals and gaskets and re tourque everything to spec.While your in there a top end...

I’m just going to use what I have as far as the 2 hulls if need be.Thanks for posting the thread.There are a couple good build threads on here that are great guidelines and advice.Going to take my...

Thanks for the reply sounds like a cool project but I have two 650 hulls to play with and a **** ton of parts.I’m just going to cut one up and rocker the nose and then re glass the front.

Looking to build a surf ski out of a few 650sx hulls if I can get some of the parts needed.Anyone out there with a project they didn’t finish.

Thanks for the reply.I picked up another parts ski that has a decent motor.I have a couple of parts hulls now I’m thinking about building a surf ski.

Sold for $250 shipped

$60 shipped for 550 nose braces563191

Grips- odi lock on or vintage hydrosport/ame
Billet trigger throttle lever
Hydro turf mat molded I prefer over cut or grooved
Impeller-skat or Silas-you can go variable pitch but depending on the...

No expert either but go through the usual problems and if you can’t get it to run or pull better compression your plan sounds like a good one.Cant go wrong with group K and being able to use pump gas...

I sent you a pm with my cell but as far as north shore vs. south shore,the surf on the south is a lot better for free ride.My son goes through the Moriches inlet to get out into the ocean.He built up...

Looking for a clean cylinder or low hours motor for 650sx.text me if you want to sell or trade.(631)278-4290

Thanks,
Anthony

Brenton check eBay there are a few for sale.I saw a Mariner up for best offer but Coffman and Kerker or PJS pop up here and there.FP will be hard to find.Facebook also is hit or miss but it worth a...

Bought the tank to use on a conversion.Doesnt fit with the 650 motor in a 550 hull.Includes pickups, gas cap and 2 brackets to use in place of the stock bracket.Pm or text me if interested at...

Haha,I’m glad this thread didn’t turn into an argument over decals.I bought the stickers from Darren amongst other parts and he is a good guy.Just getting back into it with my son and turned his...

Don’t buy anything from Greg Roberts.He tried scamming me as well as others.

Extended ride plates change riding conditions in other areas as for as freestyle and surf .They also make angled pump spacers for the nozzle that aren’t expensive and help keep from porpoising.

JRdillon is a legit seller and he has some custom ones he made is various lengths.Try to pm him,not sure if he is selling But it’s worth a shot.It takes at least 2 or 3 ride plates to extend them...

This is like the twilight zone with the scammers on this site.Greg Roberts pm me trying to sell me a waterbox.Above in this thread it looks like he just copied what bionic is legit selling.They’re...

I like to stay away from the to good to be true deals and I have 2 of them and one is brand new in the box.yeah ok and I get to pick the color too.The next guy to contact me spamming better have an...

I got hit up by someone again the same m/o just different names.Made him do a little leg work digging up random pics on the web of stuff they don’t even know about and then get pissed off when you...

I was looking as well for a little while but decided to go with the WC.Its set up for double cooler lines.The FP has a single line if I’m not mistaken so would have to be tapped if you plan on...

Kindly leave the site.You probably don’t even know what am igniter is and will send generic pics off the web.

The scammer must have changed his email and used Id .A lot of people looking for parts in the classifieds got hit up by the same person.They actually texted me earlier and I had a little fun with...

So 120/140 go with.thanks for the info

Yes black.the silver model I think is just the regular sbn.Black was the high performance model that needs the primer but I could be wrong.Only did some minor research on it.Thought they were bolt on...